New Fashion Design for SV-9300 Fireproof silicone sealant for Estonia Factories

New Fashion Design for
 SV-9300 Fireproof silicone sealant for Estonia Factories
  • New Fashion Design for
 SV-9300 Fireproof silicone sealant for Estonia FactoriesNew Fashion Design for
 SV-9300 Fireproof silicone sealant for Estonia Factories

Short Description:

Description SV – 9300 Fire resistant silicone sealant is a one-component, neutral-curing silicone sealant exhibiting superior performance in applications where sealing openings in walls and floors are needed to control the spread of fire, smoke, toxic gasses, and water during fire conditions.   Where to use It is an ideal material designed for use in fire-stop systems for through penetrations and joints. This product excels in applications where greater water resistance is required e.g. ...


Product Detail

Attentions

Application

Product Tags

Reliable quality and good credit standing are our principles, which will help us at a top-ranking position. Adhering to the tenet of "quality first, customer supreme" for New Fashion Design for SV-9300 Fireproof silicone sealant for Estonia Factories, If you are interested in our products, please feel free to send us your inquiry. We sincerely hope to establish win-win business relationships with you.


Description

SV – 9300 Fire resistant silicone sealant is a one-component, neutral-curing silicone sealant exhibiting superior performance in applications where sealing openings in walls and floors are needed to control the spread of fire, smoke, toxic gasses, and water during fire conditions.

 

Where to use

It is an ideal material designed for use in fire-stop systems for through penetrations and joints. This product excels in applications where greater water resistance is required e.g. curtain wall, building facade, expansion/pipe and cable joints.

 

Key Features

1. 100% silicone

2. Excellent weatherproofing and waterproofing

3. Low gas transmission rate

4. With highly efficient redundant

 

Basic Application

1.Building fire seam sealed

2.Building façade

3.cable joints

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 Flow, sagging or vertical flow mm 0
GB13477 Operating time min 15
GB13477 surface drying time(25℃,50%R.H.) min 40-60
Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃,50%R.H.
GB/T 531.1-2008 Durometer Hardness Shore A 20-60
GB13477 60% elongation of cementation   no damaging
GB13477 Elongation limit % 120
GB/T 24267 Sealant level   20HM
GB/T 24267 Fire prevention level   FV-0

 

Certification

GB/T 24267-2009

 

Color

Black

 

Package

300ml in cartridge * 24 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Check out our blog for clickable links to the items below!
    Blog- https://www.heywandererblog.com/2017/06/diy-stock-tank-pool-everything-you-need.html
    Instagram- www.instagram.com/heywanderer
    E-mail- heywanderer@gmail.com

    Things you will need:
    - Stock tank (size of your choosing- ours is 8 ft.)
    - Above Ground Pool Pump
    - Weatherproof Silicone Sealant
    - Hole Saw with Arbor
    - Plunger Valves
    - Pool Outlet
    - 1-3 Rubber Washers (or Gaskets)
    - 1 Strainer Nut

    Other things you will need for maintenance:
    - Chlorine Tablets
    - Floating Pool Dispenser
    - Water Testing Kit

    Step 1- Find a nice level area to lay the stock tank on. If the area where you have chosen isn’t level, use sand or rocks to build up whatever side needs it. It is very important that your stock tank be level so there aren’t any unexpected leaks.
    Step 2- Cut holes in your stock tank. I’m not going to lie- this is a pain in the butt. We bought a hole saw with an arbor and it took two people to get through the metal. You will need two holes, one at the top and one at the bottom. In an above ground pool, these aren’t usually right on top of each other, but ours are. We haven’t ever seen this as a problem.
    Step 3- Start assembling the parts. In the pool pump package there is a packet with instructions, warnings and troubleshooting. This packet proved to be vital in the setup of the pool. I did end up getting 2 gaskets for the bottom section (the drain section), one for the inside of the pool and one for the outside. It only says you need one for the inside, but this was causing a drip for us. I also put thread seal tape around the connections that were closest to the pool. There are a lot of connections, and each one has a gasket, so you could probably get away without the tape. I didn’t put it on all the connections, the only ones that really seemed to matter were the ones that are connecting the hoses to the pool.
    Step 4- Apply silicone waterproof sealant around all crevices involving the input and output parts. I did this on the inside of the pool and the outside. And I applied it VERY HEAVILY and did two layers, allowing one to dry before the second was applied. Sealing these crevices is one of the most important parts. This is what is going to keep the water in the pool. Well all of these steps are leading up to keeping water in the pool, but if there is any chance that it’s going to be getting out, this is what will save you.
    Step 5- Test for leaks. Before I added water to the pool, I took a water bottle and poured a good amount of water on the input and output parts. You could also just use a water hose. I would make sure the hose wasn’t on full blast. You don’t want to accidentally penetrate the sealant.
    Step 6- Once you are sure there aren’t any leaks, fill the pool just above the bottom hole/output. Check again to see if any leaks have started. If there aren’t any, fill the rest of the pool up!
    Step 7- Turn the pump on. Make sure both plunger valves are open/unlocked. When you first do this water may not come out of the output, but there is a solution! Twist off the knob on top of the filter pump to let some air out. Some water may escape too and that’s okay, just be ready to screw it back on as soon as the water starts coming out.



    Our LIXIN machines are popular used in pvc rubber label,pvc logo,pvc rubber patches,pvc keychain,pvc pen drive cover and other pvc gifts making.

    With the India office in Noida,we keep all the sample machines here for customers visiting and showing demo.we offer long term after-sale-service here.we are try to offer the best service and help our customer get more profit by buying our machines.

    Allen :+91-7503566557 sales@gobohk.com
    Dongguan Lixin Machinery CO.,LTD www.gobohk.com
    India office:A-60A,Sector 63,Noida U.P

    Related Products

    WhatsApp Online Chat !