Good User Reputation for SV-9300 Fireproof silicone sealant to Mombasa Factory
Description SV – 9300 Fire resistant silicone sealant is a one-component, neutral-curing silicone sealant exhibiting superior performance in applications where sealing openings in walls and floors are needed to control the spread of fire, smoke, toxic gasses, and water during fire conditions. Where to use It is an ideal material designed for use in fire-stop systems for through penetrations and joints. This product excels in applications where greater water resistance is required e.g. ...
Our company sticks to the principle of "Quality is the life of the company, and reputation is the soul of it" for Good User Reputation for SV-9300 Fireproof silicone sealant to Mombasa Factory, We look forward to supplying you with our products in the near future, and you will find our quotation is very reasonable and the quality of our products is very excellent!
SV – 9300 Fire resistant silicone sealant is a one-component, neutral-curing silicone sealant exhibiting superior performance in applications where sealing openings in walls and floors are needed to control the spread of fire, smoke, toxic gasses, and water during fire conditions.
Where to use
It is an ideal material designed for use in fire-stop systems for through penetrations and joints. This product excels in applications where greater water resistance is required e.g. curtain wall, building facade, expansion/pipe and cable joints.
1. 100% silicone
2. Excellent weatherproofing and waterproofing
3. Low gas transmission rate
4. With highly efficient redundant
1.Building fire seam sealed
Technical data sheet
|Test standard||Test project||Unit||value|
|GB13477||Flow, sagging or vertical flow||mm||0|
|GB13477||surface drying time（25℃，50%R.H.）||min||40-60|
|Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃，50%R.H.|
|GB/T 531.1-2008||Durometer Hardness||Shore A||20-60|
|GB13477||60% elongation of cementation||no damaging|
|GB/T 24267||Sealant level||20HM|
|GB/T 24267||Fire prevention level||FV-0|
300ml in cartridge * 24 per box
If you want the TDS or MSDS or other details, please contact with our sales person.
A weak link in the Dodge Grand Caravan, Town and Country, and other models is a plastic “Y pipe” heater hose fitting that begins to leak. The coolant drips directly onto the hot exhaust manifold pipe and vaporizes, resulting in coolant loss.
Often times the coolant loss will seem to be a mystery because there are no visual wet spots due to the instant vaporization. It is only when the leak becomes very bad that white smoke might be visible rising from under the hood, this is actually water vapor. This can be determined by the lack of a burning smell. The leaks often aren’t apparent unless you are looking at the fixture with the engine running at high RPM’s. The leak may be non existent or minimal at idle.
The fix is simple and inexpensive, $15 and 15 minutes. No previous auto repair experience should be necessary. You will need the following items.
-Y-Pipe heater fitting Murray part number 84757 or equivalent.
-3/4″ or larger hose clamps
-1 foot of 5/8″ Heater Hose
-Something to cut the hose with
-Screwdriver to tighten the new hose clamps
-Pliers to help remove an old clamp
Procedure: (Follow at you own rise)
1. Some coolant will be spilled, but not much. You can drain it if you wish or just put a tray under the vehicle to catch it.
2. Install the heater hose on the singular end of the new Y-pipe with a hose clamp.
3. Use pliers to loosen the hose clamp where the old Y-pipe attaches to the motor.
4. The factory Y-pipe is held on with permanent clamps. Simply cut the two rear hoses as close to the Y-pipe as you can. Within an inch or so is good.
5. Twist the old Y pipe to break the bond where it is attached to the engine fitting, pull it off.
6. Put the new Y-pipe in place, attaching the two rear hoses. If you have trouble sliding them on then moistening and/or twisting it can help.
7. Cut the new heater hose to length and slide it onto the engine fitting.
8. Secure all fittings with hose clamps. Don’t overtighten.
9. Clean up any coolant to protect children, animals, and the environment.
10. Bask in the feeling of a job well done!
NOTE: Some people have reported using a T fitting instead of a Y shape. I don’t know if the Y shape makes any difference or not with the smooth flow of coolant. T fittings are available in metal which can reduce the potential of cracking but also introduces the possibility of corrosion. Be sure the metal will not interact with the coolant’s chemistry or with that of other metals on the vehicle.
I found this repair on the Tear it up, Fix it, Repeat blog at…