Wholesale Price China Siway SV-602 Epoxy Structural Adhesive A/B to Plymouth Manufacturer

Wholesale Price China
 Siway SV-602 Epoxy Structural Adhesive A/B to Plymouth Manufacturer
  • Wholesale Price China
 Siway SV-602 Epoxy Structural Adhesive A/B to Plymouth ManufacturerWholesale Price China
 Siway SV-602 Epoxy Structural Adhesive A/B to Plymouth Manufacturer

Short Description:

Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.   Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...


Product Detail

Attentions

Application

Product Tags

With advanced technologies and facilities, strict quality control, reasonable price, superior service and close co-operation with customers, we are devoted to providing the best value for our customers for Wholesale Price China Siway SV-602 Epoxy Structural Adhesive A/B to Plymouth Manufacturer, We hope to establish more business relationships with customers all over the world.


Description

SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.

 

Key Features

1. Room temperature curing Epoxy adhesive

2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)

3. Mix ratio of 1:1 by volume or by weight

4. Good mechanical property

5. Bonds a wide variety of building materials

6. Good waterproofing and chemical resistance

 

Basic Application

1, the external walls of stone material, ceramic and other hang bond;

2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;

3, concrete, stone and so on crack repair;

4, the structure of the localization, anchor, reinforcement and reinforcement.

 

Technical data sheet

The following data is for reference only and is not recommended for the specification

Shear strength Stainless steel-stainless steel/Standard conditions ≥18   JC887-2001
Pressure shear strength Stone-stone/ Standard conditions ≥12
Stone-stone/ The freeze-thaw cycle 50 times ≥10
Stone – stainless steel/ Standard conditions ≥12
Standard conditions:Temperature=23℃,relative humidity=50%,48 hours curing
attribute SV-602-A SV-602-B SV-602(After mixing)
Colour gray white grey
Density(g/cm³) 1.8 1.8 1.8
Viscosity(PaS) 200-400 150-250  
Effective operating time(23℃) N/A N/A 20min
           

 

Certification

JC 887-2001

 

Color

Part A-Grey Paste/Part B-White Paste

 

Package

9kg/9kg per unit and 15kg/15kg per unit

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Be sure to subscribe to my sponsor Cottage Life! Check out their channel here: https://www.youtube.com/user/CottageLifeMagazine
    Here’s their Floating Hot Tub video, pretty sweet: https://youtu.be/zApeT-AebMg
    v v v v v v v Click ‘Show more’ v v v v v v v

    I took up running these past few years as an extra hobby to allow me some thinking time away from the computer and all my camera gear. I looked into purchasing some of these minimalist shoes both for running as well as for a water shoe for fishing but found that my local stores didn’t carry any in stock, and buying shoes online can be risky for fitting purposes. Why not make some myself then?

    I didn’t believe that spray rubber would work very well at first and assumed that I would have to use the liquid paint-on variety that comes in a tin to achieve a good coating on the fabric, but after testing the spray rubber for myself I didn’t even bother with any other method. It works excellent. The rubber is more durable than expected, and after about a quarter mile on very sharp gravel I noticed no wear at all.

    One issue that I do have with the shoes is that some of the rubber solvent absorbed into the fabric outside the spray area, carrying trace amounts of rubber with it. This was due to my impatience in adding too much rubber in the first coat which wet the fabric too much and caused unsightly stains that you can see on top of the toes in the video, and also caused a little bit of extra stiffness in those areas. This should be an avoidable issue by simply going a little more slowly until there is a good rubber surface established over the absorbent fabric. There shouldn’t be much to worry about after the first coat or two is added.

    One other very minor improvement I would make in my next pair of shoes is to make the heel more narrow while spraying on the rubber. While I shaped the socks fairly accurately to the natural shape of my feet, I would have preferred the heel to be a little narrower so that it was a snugger fit. That’s mostly a matter of preference and doesn’t contribute one way or the other toward function.

    Items used for this project:

    Divided Toe Socks
    Spray Rubber
    Plastic Grocery Bags
    Coat Rack (Or anything else that can hold the socks upright – two sticks would do fine)
    Fan (For both ventilation as well as increasing solvent drying time) #NightHawkInLight

    -~-~~-~~~-~~-~-
    Check out my latest video: “How To View Invisible Air Currents With Lasers”

    -~-~~-~~~-~~-~-



    Hongye silicone rubber Model No.: HY-6 series. Eg.: HY-628, HY-638.

    Price: 5.98-9.28USD/KG, FOB, by sea/ Shenzhen port

    Features of Hongye silicone for mold making:
    (1) High tensile & tear strength
    (2) High duplication times
    (3) Low linear shrinkage
    (4) Resistance to high-temperature
    (5) Low shrinkage and non-deformation
    (6) Resistance to acid-alkali and expansion

    Operation instructions for silicon rubber mold making
    Step One: Take 100g of part A and add 2g of part B and mix the silicone rubber and curing agent evenly.

    Step Two: vacuum pumping
    Without exception, this step takes less than 10 minutes.
    Note: The time for vacuum-pumping should be less than 3-5 minutes. Otherwise, once the silicone rubber has cross-link reaction during vacuum pumping process, it will not be operated.

    Step Three: Pouring the vacuumed silicone mixture into the frame with original mold.

    For more information, pls feel free to contact Miss Gloria.
    Tel: +86-755-89948006
    Fax: +86-755-89948030
    Mob: +86-18938867584
    E-mail: hyxf@szrl.net
    Gmail: gloriachan0901@gmail.com
    QQ: 1034964130
    Welcome to our website https://www.szrl.net

    Related Products

    WhatsApp Online Chat !