Renewable Design for SV-8000 PU Sealant for Insulating Glass for Florence Importers

Renewable Design for SV-8000 PU Sealant for Insulating Glass for Florence Importers
  • Renewable Design for SV-8000 PU Sealant for Insulating Glass for Florence ImportersRenewable Design for SV-8000 PU Sealant for Insulating Glass for Florence Importers

Short Description:

Description SV – 8000 two-component polyurethane insulating glass sealant is a neutral cure, mainly used for the insulating glass of the second seal. Product formulation to use its performance with high modulus, high strength, to meet the requirements of insulating glass assembly.   Where to use It is a two-component PU sealant that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.   Key Fe...


Product Detail

Attentions

Application

Product Tags

We depend on sturdy technical force and continually create sophisticated technologies to meet the demand of Renewable Design for SV-8000 PU Sealant for Insulating Glass for Florence Importers, Our professional technical team will be wholeheartedly at your service. We sincerely welcome you to visit our website and company and send us your inquiry.


Description

SV – 8000 two-component polyurethane insulating glass sealant is a neutral cure, mainly used for the insulating glass of the second seal. Product formulation to use its performance with high modulus, high strength, to meet the requirements of insulating glass assembly.

 

Where to use

It is a two-component PU sealant that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.

 

Key Features

1. High Modulus

2. UV resistance

3. Low vapor and gas transmission

4. Primerless adhesion to coated glass

 

Technical data sheet

Test project standards Value
Sagging degree (mm) ≤3 0
Operating time ≥30 30
Thermal weight loss(%) ≤10 2
Durometer Hardness Shore A 20-80 42
tensile propcrties(MPA) >0.4 1.0
Bond damage area(5%) ≤5 0

 

Certification

GB-24266-2009;

 

Color

Component A(Base) – White, Component B(Catalyst)- Black

 

Package

1. Component A(Base): (190L), Component B(Catalyst) (18.5L)

2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

 

  • Previous:
  • Next:



  • Over time I’ve been noticing small cracks appearing on my Keystone Cougar fifth wheel trailers plastic fenders. The cracking is taking place around the screws holding the fenders to the trailer sidewall. It started off with one or two but is slowly progressing to more and more every year. If this kept up and left unchecked, I fear one day I’d lose a fender during travel.

    So, I decided this summer to pull the fenders off and see what could be done to beef them up, stop the cracking and prevent a full on failure. A reader recently contacted me via email with some insight to the problem. He believes the cracking might be caused by the indented area for the screws not being flush with the backside. 

    Ray,
    At the end of your shelf repair video, you showed a shot of the cracks around the mounting screws for the fenders.
    I just removed the fenders from my trailer so I could caulk the steel wheel tubs to the side of the trailer.
    Upon reinstallation of the plastic fenders, I noticed that the indents for the screws are not flush with the back side.
    If you over tighten the screws it is going to crack the plastic.
    There is room enough to put a washer between the fender and the sidewall.
    You might be able to epoxy a washer on the back side to reinforce the plastic.
    I enjoy your videos.
    Arthur

    I elected to take Arthur’s advice and use some washers on the back side of the fender behind the screw holes. Instead of using epoxy I chose to use SikaFlex 291 sealant. I embedded the washer into the Sikaflex and then applied a healthy layer of it all around the indented plastic area. On the front side of the fender behind each screw, I added a small rubber grommet.

    Time will tell but I believe the repair and modifications made should help extend the life of my fenders and at least prevent a catastrophic failure at speed on a highway. If not, thanks to thunderbird97 on YouTube for pointing me to a website to order up a replacement set.

    “thunderbird97 - Ray here is a website I ordered my fender skirts in case you need it, https://www.icondirect.com , the only difference was old ones were thicker, new ones are made out of better material, holes matched up perfect.  Here is the Canada site www.icondirect.ca”

    ———————————–
    Follow our RVing adventures at https://www.loveyourrv.com and https://rvhappyhour.com

    Connect with Love Your RV!

    Pinterest ► https://www.pinterest.com/loveyourrv
    Google+ ► https://plus.google.com/+LoveYourRVonGPLUS
    Facebook ► https://www.facebook.com/LoveYourRV
    Twitter ► https://twitter.com/loveyourrv
    Blog Feed ► https://feeds.feedburner.com/LoveYourRV
    Monthly Newsletter ► https://www.loveyourrv.com/mailing-list-sign-up/

    Don’t forget to Subscribe! ► https://www.youtube.com/subscription_center?add_user=LoveYourRV



    Malaysia custom testing them 2 sets 30L dual planetary mixer hydraulic pressing machine these both days. all is ok now, they are very satisfied and than is arrange the shipping.
    008618921164168 is whatsapp and dhynzx@hotmail.com is email ID, if you are also interest in the Dual planetary mixer or industry mixer or chemical mixer for making the paint ,battery paste, solder paste, ceramic paste, silicone inks, sealants, structure adhesives, soft cream, jam ect

    Related Products

    WhatsApp Online Chat !