Renewable Design for SV-777 silicone sealant for stone for Iceland Factories

Renewable Design for
 SV-777 silicone sealant for stone for Iceland Factories
  • Renewable Design for
 SV-777 silicone sealant for stone for Iceland FactoriesRenewable Design for
 SV-777 silicone sealant for stone for Iceland Factories
  • Renewable Design for
 SV-777 silicone sealant for stone for Iceland FactoriesRenewable Design for
 SV-777 silicone sealant for stone for Iceland Factories
  • Renewable Design for
 SV-777 silicone sealant for stone for Iceland FactoriesRenewable Design for
 SV-777 silicone sealant for stone for Iceland Factories

Short Description:

Description SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials.   Key Features 1. 100% silicone 2. Minimized fluid migration 3. Low dirt pick up 4. Water &...


Product Detail

Attentions

Application

Product Tags

"Based on domestic market and expand overseas business" is our development strategy for Renewable Design for SV-777 silicone sealant for stone for Iceland Factories, We also ensure that your selection will be crafted with the highest quality and reliability. Please feel free to contact us for further information.


Description

SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials.

 

Key Features

1. 100% silicone

2. Minimized fluid migration

3. Low dirt pick up

4. Water & weatherproof

5. Primerless adhesion to most building materials

6. 25% movement capability

 

Basic Application

1.Stone curtain wall sealing

2.Engineering ceramic sealing

3.Stone and other materials such as glass, metal seam sealing

4.Other uses

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
ASTM C 679 Flow, sagging or vertical flow mm 0
  VOC g/L <80
GB13477 surface drying time(25℃,50%R.H.) min 30
  Curing time(25℃,50%R.H.) Day 7-14
Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃,50%R.H.
GB13477 Durometer Hardness Shore A 30
GB13477 The ultimate tensile strength Mpa 0.7
  Temperature stability -50~+150
GB13477 Movement capability % 25
ASTM C 1248 Pollution / oil, natural stone   No

 

Certification

25HM GB/T 23261-2009;ASTM C920-2011

 

Color

Black,White,Gray

 

Package

300ml in cartridge * 24 per box, 590ml in sausage *20 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Installation Instructions for an ASI Soundproof Door – High Definition version

    The wall that this was installed to was treated with products, too. You can view our video on Soundproofing a Wall (https://www.youtube.com/watch?v=rVtY6MZoFrY) for more information.

    https://www.acousticalsurfaces.com/acoustic_doors/soundproof_doors.htm

    Tools Needed:
    -Level
    -Pencil
    -Tape Measure
    -Utility Knife
    -Cordless Drill
    -Quart-Size Caulk Gun
    -Hammer
    -Installation Kit*
    -Installation Instructions*
    -Heavy Duty Screws*
    -Shims*
    -Backer Rod*
    -Acoustical Sealant*
    -Door Hardware Kit*
    -Door Casing (One installed on door when shipped, other side comes loose)*
    -Door & Jamb*

    *Included in Door Purchase (https://bit.ly/qZQjRh)

    Make sure to inspect the door and included items for any damage prior to installation.

    INSTALLATION INSTRUCTIONS
    1. Unscrew the temporary threshold on the bottom of the door.
    2. Determine which side of the jamb the hinges will be.
    3. Measure and mark hinge locations onto the door frame.
    4. Place a set of shims at each hinge, making sure they are plumb with the level.
    5. Tip the door into place, make sure all is plumb and level.
    6. Remove the two screws in the hinge closest to the door stop.
    7. Repeat for each hinge.
    8. Prop the bottom corner of the door with it swung at 90 degrees so that it holds the jamb tight to the drywall.
    9. Pre-drill the holes from the screws you just removed to prepare for the long screws. (We use a 5/32 bit)
    10. From top hinge down, install the included long screws.
    11. Adjust shims as necessary to ensure the door stays level.
    12. Shim the strike side of the door to get an even reveal on the inside of the door.
    13. Install the backer rod around the gap in the rough opening by pushing it in about an inch deep. You can use a shim to push it in.
    14. Fill the remaining gap with acoustical sealant.
    15. Remove the temporary brace off the bottom of the trim kit.
    16. Maintaining a 1/4″ reveal, attach the trim with the supplied screws.
    17. Nail trim to wall as needed.
    18. Fill holes with wood putty and sand.
    19. Remove the short hardware screws that came shipped from the strike side of the door.
    20. Replace them with the long screws for the strike hardware to secure the framing.
    21. Remove the trim on the hinge side of the door that shipped on the door.
    22. Repeat steps 13-18 on this side of the door.
    23. Install door hardware as specified.
    24. Ensure the door is shut and latched.
    25. Adjust the door seals by locating the Phillips screws on the face of the door seal and turn counter-clockwise to tighten the door seal. This will close the gap between the seal and the door.
    26. Work the way down the seal until all screws are adjusted so that the seal comes in contact with the door slab.
    27. Trim off excess gasket on the strike side of the door jamb at the bottom so that the gasket is flush with the floor.
    28. Adjust the bottom drop seal by loosening the set screw at the top of the drop seal counter-clockwise. When the screw engages the stop on the jamb, it will drop the seal down.
    29. Peel off the backer on the peel-and-stick seal cover panels and pressure fit over door seals. Start with the top and fit the sides into the miter.



    Gorilla Grab adhesive is one of the strongest grab adhesives we have used in 45 years of being in the trade. It runs smoothly out of the tube, it sticks to pretty much anything and there is no question it should be in everyones toolbag. It even works under water.

    Related Products

    WhatsApp Online Chat !