Rapid Delivery for Siway SV-602 Epoxy Structural Adhesive A/B to Colombia Manufacturer

Rapid Delivery for Siway SV-602 Epoxy Structural Adhesive A/B to Colombia Manufacturer
  • Rapid Delivery for Siway SV-602 Epoxy Structural Adhesive A/B to Colombia ManufacturerRapid Delivery for Siway SV-602 Epoxy Structural Adhesive A/B to Colombia Manufacturer

Short Description:

Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.   Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...


Product Detail

Attentions

Application

Product Tags

We are experienced manufacturer. Wining the majority of the crucial certifications of its market for Rapid Delivery for Siway SV-602 Epoxy Structural Adhesive A/B to Colombia Manufacturer, Our professional technical team will be wholeheartedly at your service. We sincerely welcome you to visit our website and company and send us your inquiry.


Description

SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.

 

Key Features

1. Room temperature curing Epoxy adhesive

2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)

3. Mix ratio of 1:1 by volume or by weight

4. Good mechanical property

5. Bonds a wide variety of building materials

6. Good waterproofing and chemical resistance

 

Basic Application

1, the external walls of stone material, ceramic and other hang bond;

2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;

3, concrete, stone and so on crack repair;

4, the structure of the localization, anchor, reinforcement and reinforcement.

 

Technical data sheet

The following data is for reference only and is not recommended for the specification

Shear strength Stainless steel-stainless steel/Standard conditions ≥18   JC887-2001
Pressure shear strength Stone-stone/ Standard conditions ≥12
Stone-stone/ The freeze-thaw cycle 50 times ≥10
Stone – stainless steel/ Standard conditions ≥12
Standard conditions:Temperature=23℃,relative humidity=50%,48 hours curing
attribute SV-602-A SV-602-B SV-602(After mixing)
Colour gray white grey
Density(g/cm³) 1.8 1.8 1.8
Viscosity(PaS) 200-400 150-250  
Effective operating time(23℃) N/A N/A 20min
           

 

Certification

JC 887-2001

 

Color

Part A-Grey Paste/Part B-White Paste

 

Package

9kg/9kg per unit and 15kg/15kg per unit

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:




  • You can view photos of the porch that were taken March, 2013.

    https://s1281.photobucket.com/user/768kayshan/library/?sort=3&page=1

    It’s been almost 2 years, & this faux application has held up well to both weather & daily use.

    Think of this project as being like a texture paint application using a mix of vinyl concrete patcher & dye.

    Materials I Used:
    - Dust mask & gloves
    - Mixing buckets & spatulas/scrappers
    - Paint brushes (One extra soft bristle brush for cleaning off faux bricks/stone after peeling up tape).
    - Paint Stripper
    - Heavy duty power washer
    - Vinyl concrete patcher (this was the only type of concrete mix used for entire project)
    - Cement dye (Red, Buff, & Charcoal)
    - 1/2″ masking tape ( I found this tape at an auto body repair shop).
    - Concrete bonding agent
    - Concrete sealer
    - Heavy duty exterior white paint for the foundation & porch posts.

    Steps:
    - Apply paint stripper to loosen old paint on porch & then remove all old paint w/ a heavy duty power washer (I rented mine at Home Depot’s tool rental).

    - After porch is clean & dry apply the concrete bonding agent. Allow it to dry according to instructions on bottle.

    First Layer:
    - The first layer will become the color/texture of your faux grout lines. If you have a cement surface that is in good condition I would clean it, apply bonding agent, & after it is dry tape out the pattern for your brick or stone layer. In other words, your original surface will become your grout lines. If you have any cracks or slight dips you can repair them w/ this first layer application of vinyl concrete patcher. Vinyl patcher is stronger than regular cement & will maintain its strength w/ a layer spread as thin as 1/16″ thick(my personal experience w/ this product). Mix Vinyl patcher w/ water (follow directions on bag). The natural color of this product is light grey(or could also be white..so read the bag before you buy). No need to dye this first layer if you like its natural color for your grout..I didn’t dye mine. Apply a thin, smooth, flat layer, & allow to dry. Once dry, if you accidentally have any spots that are too high or pointy you can file them down w/ a cement grinder…but, overall, it may not be necessary since you should be able to blend in slightly high or pointy spots w/ your next layer of faux brick/stone.

    - Tape out any pattern you like.

    Second Layer:
    - Mix some vinyl patcher w/ whatever color dye you like. This will vary depending on what kind of stone/brick design you want on your porch. For example, I mixed one bucket of red dye & a separate bucket of buff dye for my bricks. I then scraped on a thin layer of red & then a thin layer of buff on top (or you can do vice versa), all while cement was wet..this mix of layering the two colors gave the bricks each their own individual & more natural look. Also, keep in mind that your wet cement will become several shades lighter after it dries.

    - Allow your cement to dry to a soft, dry, dough-like consistency.. something similar to a raw pie shell dough (If it’s too wet, too much of your cement will pull off w/ the tape. If it’s too dry, you’ll have a difficult time pulling the tape off). Gently & slowly pull up the tape, & gently brush away the little pieces of debris using a VERY soft bristle brush (invest in a well made soft bristle brush..cheap, rough, brushes will drop bristles in your work & may leave brush textures on your concrete).

    - Let your handy work dry over night..then apply a couple of coats of sealer to your entire project..make sure your sealer is specially made for fresh concrete work..some sealers can’t be applied until 90 days after your concrete cures. After 90 days, you can also apply a 90+ day sealer.

    Related Products

    WhatsApp Online Chat !