Popular Design for Siway SV-602 Epoxy Structural Adhesive A/B for Honduras Importers
Short Description:
Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion. Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...
Being supported by an advanced and professional IT team, we could offer technical support on pre-sales & after-sales service for Popular Design for Siway SV-602 Epoxy Structural Adhesive A/B for Honduras Importers, We welcome new and old customers from all walks of life to contact us for future business relationships and achieving mutual success!
Description
SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.
Key Features
1. Room temperature curing Epoxy adhesive
2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)
3. Mix ratio of 1:1 by volume or by weight
4. Good mechanical property
5. Bonds a wide variety of building materials
6. Good waterproofing and chemical resistance
Basic Application
1, the external walls of stone material, ceramic and other hang bond;
2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;
3, concrete, stone and so on crack repair;
4, the structure of the localization, anchor, reinforcement and reinforcement.
Technical data sheet
The following data is for reference only and is not recommended for the specification
Shear strength | Stainless steel-stainless steel/Standard conditions | ≥18 | JC887-2001 | ||
Pressure shear strength | Stone-stone/ Standard conditions | ≥12 | |||
Stone-stone/ The freeze-thaw cycle 50 times | ≥10 | ||||
Stone – stainless steel/ Standard conditions | ≥12 | ||||
Standard conditions:Temperature=23℃,relative humidity=50%,48 hours curing | |||||
attribute | SV-602-A | SV-602-B | SV-602(After mixing) | ||
Colour | gray | white | grey | ||
Density(g/cm³) | 1.8 | 1.8 | 1.8 | ||
Viscosity(PaS) | 200-400 | 150-250 | |||
Effective operating time(23℃) | N/A | N/A | 20min | ||
Certification
JC 887-2001
Color
Part A-Grey Paste/Part B-White Paste
Package
9kg/9kg per unit and 15kg/15kg per unit
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Whether its a minivan, SUV or station wagon, mom-mobiles get dirty…very dirty. Commuting to school, work, grocery store, sporting events and road trips really take a toll on the appearance of these vehicles. In today’s video, we go over the proper washing and drying techniques to prevent paint damage, save time and achieve the best results.
What better way to cut through daily grime, prevent swirls and have fun while you’re detailing? Using a foam cannon of course, the TORQ Big Mouth produces a TON of suds the reduce the chances of harming the paint with abrasive particles of dirt. Mr. Pink creates a thick volume of suds that enhance shine and smells great.
After working in linear motions and gently wiping away the dirt that was clinging to the surface, we finish with the drying process. Many choose the Woolly Mammoth to trap water droplets and wick them off of the paint to prevent water spots. Its large design means it can pick up more water than other towels which saves time and the need for multiple towels or passes.
••••••••••
➜ TORQ Big Mouth Foam Cannon
https://www.chemicalguys.com/TORQ_Big_Mouth_Professional_Foam_Cannon_p/eqp322.htm
➜ Mr. Pink Shampoo
https://www.chemicalguys.com/ProductDetails.asp?ProductCode=CWS_402_16&Click=18676&utm_source=Social&utm_medium=YouTube&utm_campaign=CWS_402_16
➜ Dirt Trap Bucket Insert
https://www.chemicalguys.com/ProductDetails.asp?ProductCode=DIRTTRAP&Click=18676&utm_source=Social&utm_medium=YouTube&utm_campaign=DIRTTRAP
➜ Chenille Microfiber Wash Mitt
https://www.chemicalguys.com/ProductDetails.asp?ProductCode=MIC_493&Click=18676&utm_source=Social&utm_medium=YouTube&utm_campaign=MIC_493
➜ Diablo Wheel Gel
https://www.chemicalguys.com/ProductDetails.asp?ProductCode=CLD_997_16&Click=18676&utm_source=Social&utm_medium=YouTube&utm_campaign=CLD_997_16
➜ Woolly Mammoth Drying Towel
https://www.chemicalguys.com/ProductDetails.asp?ProductCode=MIC_1995&Click=18676&utm_source=Social&utm_medium=YouTube&utm_campaign=MIC_1995
••••••••••
● Website: www.ChemicalGuys.com
● Subscribe to our channel: https://www.youtube.com/subscription_center?add_user=chemicalguys
● Subscribe to our newsletter: https://www.chemicalguys.com/category_s/239.htm
● Like Us on Facebook: https://www.facebook.com/Chemical-Guys-159949434070452/
● Follow us on Instagram: https://www.instagram.com/chemicalguys/
A simple and very cheap way to make custom shaped moulds for creating simple resin castings with or without an LED embedded into them.
The mould is based on a popular technique on the Internet which uses common household materials to make good silicone rubber moulds. It’s basically just standard sealant silicone mixed with cornflour (cornstarch) to make a malleable putty into which your master shape is pressed. If using non plastic masters then apply some oil or Vaseline to the object so that the silicone doesn’t stick to it.
When the mould has cured in an hour or so (but leave overnight if possible) then the master can be removed and the flexible mould can then be used to produce replicas from various resins. I like the simplicity of the two part syringe resins which can be bought at dollar store type shops.
To embed an LED I prefer to use the shorter “strawhat” 4.8mm LEDs as it helps to keep the chip as far back from the front of the casting as possible for good light distribution. Bend the leads to the side at right angles to the LED so that it can be placed across the top of the mould with the LED submerged in the resin.