OEM/ODM Manufacturer SV-999 Structural Glazing Silicone Sealant to Rio de Janeiro Manufacturer

Innovation, quality and reliability are the core values of our company. These principles today more than ever form the basis of our success as an internationally active mid-size company for OEM/ODM Manufacturer SV-999 Structural Glazing Silicone Sealant to Rio de Janeiro Manufacturer, Welcome to visit us at any time for business relationship established.

Description

SV – 999 silicone structural sealant is a one-component, neutral curing, designed for glass curtain wall, aluminum curtain wall, glass daylighting roof and metal structural engineering structural assembly silicone sealant. Show the effective physical properties and bonding performance

Key Features

1. 100% silicone

2. No sag

3. Strong bonding strength

4. Water & weatherproof

5. Primerless adhesion to most building materials

6. 25% movement capability

Basic Application

1.Glass curtain wall, aluminum curtain wall structure adhesive seal

2.Glass daylighting roof, metal structure engineering

3.Insulating glass bonding

Technical data sheet

Certification

GB 16776；ASTM C1184

Color

Black

Package

300ml in cartridge * 24 per box, 500ml in sausage *20 per box

Shelf life

12 months

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

Installation Instructions for an ASI Soundproof Door – High Definition version

The wall that this was installed to was treated with products, too. You can view our video on Soundproofing a Wall (https://www.youtube.com/watch?v=rVtY6MZoFrY) for more information.

https://www.acousticalsurfaces.com/acoustic_doors/soundproof_doors.htm

Tools Needed:
-Level
-Pencil
-Tape Measure
-Utility Knife
-Cordless Drill
-Quart-Size Caulk Gun
-Hammer
-Installation Kit*
-Installation Instructions*
-Heavy Duty Screws*
-Shims*
-Backer Rod*
-Acoustical Sealant*
-Door Hardware Kit*
-Door Casing (One installed on door when shipped, other side comes loose)*
-Door & Jamb*

*Included in Door Purchase (https://bit.ly/qZQjRh)

Make sure to inspect the door and included items for any damage prior to installation.

INSTALLATION INSTRUCTIONS
1. Unscrew the temporary threshold on the bottom of the door.
2. Determine which side of the jamb the hinges will be.
3. Measure and mark hinge locations onto the door frame.
4. Place a set of shims at each hinge, making sure they are plumb with the level.
5. Tip the door into place, make sure all is plumb and level.
6. Remove the two screws in the hinge closest to the door stop.
7. Repeat for each hinge.
8. Prop the bottom corner of the door with it swung at 90 degrees so that it holds the jamb tight to the drywall.
9. Pre-drill the holes from the screws you just removed to prepare for the long screws. (We use a 5/32 bit)
10. From top hinge down, install the included long screws.
11. Adjust shims as necessary to ensure the door stays level.
12. Shim the strike side of the door to get an even reveal on the inside of the door.
13. Install the backer rod around the gap in the rough opening by pushing it in about an inch deep. You can use a shim to push it in.
14. Fill the remaining gap with acoustical sealant.
15. Remove the temporary brace off the bottom of the trim kit.
16. Maintaining a 1/4″ reveal, attach the trim with the supplied screws.
17. Nail trim to wall as needed.
18. Fill holes with wood putty and sand.
19. Remove the short hardware screws that came shipped from the strike side of the door.
20. Replace them with the long screws for the strike hardware to secure the framing.
21. Remove the trim on the hinge side of the door that shipped on the door.
22. Repeat steps 13-18 on this side of the door.
23. Install door hardware as specified.
24. Ensure the door is shut and latched.
25. Adjust the door seals by locating the Phillips screws on the face of the door seal and turn counter-clockwise to tighten the door seal. This will close the gap between the seal and the door.
26. Work the way down the seal until all screws are adjusted so that the seal comes in contact with the door slab.
27. Trim off excess gasket on the strike side of the door jamb at the bottom so that the gasket is flush with the floor.
28. Adjust the bottom drop seal by loosening the set screw at the top of the drop seal counter-clockwise. When the screw engages the stop on the jamb, it will drop the seal down.
29. Peel off the backer on the peel-and-stick seal cover panels and pressure fit over door seals. Start with the top and fit the sides into the miter.

Before using this product, please read all instructions and test a small area of your doll’s tear before using it. Precede at your own risk! Hope this video helps. Thanks for watching!

https://www.smooth-on.com

FIND MY BABIES ON INSTA

https://www.instagram.com/kelseys_cradle/

DISCLAIMER: Yes, the babies in my videos are fake. I repeat, the babies are reborn dolls, not humans. Yes, I pretend they are real for the sake of videos and my own enjoyment. This is a hobby like collecting and playing with trains or fantasy football. I am not crazy. If you don’t like the hobby of collecting and role playing with reborn dolls, please do not watch my videos.