OEM Customized wholesale SV-888 Weatherproof Silicone Sealant Export to Bangladesh
Description SV-888 silicone weatherproof sealant is one component, neutral cure silicone sealant, designed for glass curtain wall, aluminum curtain wall and building exterior design, has excellent weathering properties, it can form durable and most building materials, waterproof and flexible interface. Key Features 1. 100% silicone 2. Medium modulus (25% movement capability) 3. UV resistance & weatherproof 4. Primerless adhesion to most building materials Basic Application 1.All ...
We have the most advanced production equipment, experienced and qualified engineers and workers, recognized quality control systems and a friendly professional sales team pre/after-sales support for OEM Customized wholesale SV-888 Weatherproof Silicone Sealant Export to Bangladesh, welcomes all overseas friends and merchants to establish collaboration with us. We will provide you with honest, high quality and efficient service to meet your requirements.
SV-888 silicone weatherproof sealant is one component, neutral cure silicone sealant, designed for glass curtain wall, aluminum curtain wall and building exterior design, has excellent weathering properties, it can form durable and most building materials, waterproof and flexible interface.
1. 100% silicone
2. Medium modulus (25% movement capability)
3. UV resistance & weatherproof
4. Primerless adhesion to most building materials
1.All kinds of glass curtain wall weatherproof seal
2.For metal (aluminum) curtain wall, enamel curtain wall weatherproof seal
3.Joint sealing of concrete and metal
4.Roof joint seal
Technical data sheet
|Test standard||Test project||Unit||value|
|GB13477||Flow, sagging or vertical flow||mm||0|
|GB13477||surface drying time（25℃，50%R.H.）||min||20|
|Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃，50%R.H.|
|GB13477||Durometer Hardness||Shore A||28|
|GB13477||The ultimate tensile strength||Mpa||0.65|
GB/T 22083-G-35；ASTM C920
Black, white, grey
300ml in cartridge * 24 per box, 590ml in sausage *20 per box
If you want the TDS or MSDS or other details, please contact with our sales person.
Other related videos:
How to strip and repair tap gland-seal
How to stop a monobloc tap outlet leaking (emergency repair)
Earlier today I noticed some water on the floor near the kitchen sink so opened the unit and saw a bit of a leak from the main stopcock that controls flow of water from rising main into the house. Water was dripping from the gland seal. Unfortunately since this is the main way of turning off the water supply* I couldn’t isolate the actual stopcock which ironically is the isolating valve for the cold water supply. So as this was an emergency repair I had to use PTFE tape which is a product that everyone should have in their toolkit.
Anyway – to carry out emergency repair;
Turn off the stopcock and remove handle by unscrewing the cross-head screw in the end of shaft.
Loosen off the gland seal retainer collar. The leak will worsen so put some old rags around it to mop up spills.
Try to extract the old gland packing which is either rubber, fibre or leather. If the tap is in awkward place or the old seal is rock hard and too tight to remove, you then have to wrap several turns of PTFE tape around the shaft as near to the gland seal as possible.
Now using a flat screwdriver and carefully push the tape right down into the gland seal (or what’s left of it)
Now install the gland seal retainer collar and tighten it up.
Now turn on the stopcock or tap/faucet and check for leaks. Ideally the old seal/packing is removed first but in the real world that sometimes doesn’t happen. If there’s still no leaks after a few hours then chances are you’ve fixed the problem. This is a ‘temporary repair’ so ultimately you will have to fit a new stopcock/tap/valve at some point. A useful tip is to regularly cycle any water supply valves, taps etc fully open and closed to keep them from sticking open or shut. Do this twice a year. Taps tend to seize more when they are fully open so it’s good practice to open them fully then back them off half a turn so the internal valve seat isn’t hard against the end stops.
*If the main water supply stop valve is leaking you’ll either need a pipe freezing kit or hope there is a main water supply cut-off along with the water meter or supply from the mains water. Worth making a note of where the stopcocks and other valves are located on your property.
Liquid silicone rubber for mold making applications
1. Liquid silicone rubber for mold making can used for poly resin crafts, PU crafts, PU resin crafts ,gypsum crafts ,unsaturated resin crafts, lighting and candles crafts ,plastic toy , stationery gifts crafts industry,
2. Liquid silicone rubber for mold making is applicable for large statue Buddha, relieve, furniture decorative materials, statues Buddha, artifacts copied, building decoration materials, large-scale cement mold
3. Liquid silicone rubber for mold making is intend for artificial fossils Factory, Europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on.
Liquid silicone rubber for mold making features
Liquid silicone rubber for mold making is white flowing liquid with general hardness of 22-50A°after curing with features
(1) High tensile & tear strength
(2) High duplication times
(3) Low linear shrinkage
(4) Resistance to high-temperature
(5) Low shrinkage and non-deformation
(6) Resistance to acid-alkali and expansion
Liquid silicone rubber for mold making operation instructions
Step One: Take 100g of part A and add 2g of part B and mix the silicone rubber and curing agent evenly.
Step Two: vacuum pumping
Without exception, this step takes less than 10 minutes.
Note: The time for vacuum-pumping should be less than 3-5 minutes. Otherwise, once the silicone rubber has cross-link reaction during vacuum pumping process, it will not be operated.
Step Three: Brushing cast & Perfusion Molding operation
Shelf life for liquid silicone rubber for mold making
10~12months, when stored in a dry & cool place under the room temperature 25.
Packing for liquid silicone rubber for mold making
1kg/ bottle, 5 kg/drum vacuumed packing, 25kgs/drum vacuumed packing,200 kg/drum
For more information, please feel free to contact Ms. Susie
Office No.: 0086-755-89212380
Welcome to our website www dot szrl dot net