New Fashion Design for SV-8800 Silicone Sealant for Insulating Glass to Australia Manufacturer

New Fashion Design for
 SV-8800 Silicone Sealant for Insulating Glass to Australia Manufacturer
  • New Fashion Design for
 SV-8800 Silicone Sealant for Insulating Glass to Australia ManufacturerNew Fashion Design for
 SV-8800 Silicone Sealant for Insulating Glass to Australia Manufacturer
  • New Fashion Design for
 SV-8800 Silicone Sealant for Insulating Glass to Australia ManufacturerNew Fashion Design for
 SV-8800 Silicone Sealant for Insulating Glass to Australia Manufacturer
  • New Fashion Design for
 SV-8800 Silicone Sealant for Insulating Glass to Australia ManufacturerNew Fashion Design for
 SV-8800 Silicone Sealant for Insulating Glass to Australia Manufacturer

Short Description:

Description SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.   Where to use It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.   Key Features 1. High Modulus 2. UV resistance 3. Low vapor and gas transmission 4. Primerless adhesion...


Product Detail

Attentions

Application

Product Tags

owing to good service, a variety of high quality products, competitive prices and efficient delivery, we enjoy a good reputation among our customers. We are an energetic company with wide market for New Fashion Design for SV-8800 Silicone Sealant for Insulating Glass to Australia Manufacturer, Please send us your specifications and requirements, or feel free to contact us with any questions or inquiries that you may have.


Description

SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.

 

Where to use

It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.

 

Key Features

1. High Modulus

2. UV resistance

3. Low vapor and gas transmission

4. Primerless adhesion to coated glass

5. 100% compatible to SV-8890

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 Specific gravity(After mixing)   1.33
GB13477 Operating time min 20-40
GB13477 surface drying time(25℃,50%R.H.) min 80-188
corrosivity     No
7 days after curing——25℃,50%R.H.
GB/T 531 Durometer Hardness Shore A 40
GB13477 The tensile modulus at 12.5% elongation Mpa 0.18
  The ultimate tensile strength Mpa 0.92
GB13477 Elongation limit (fracture) % 150

 

Certification

GB-24266-2009;

 

Color

Component A(Base) – White, Component B(Catalyst)- Black

 

Package

1. Component A(Base): (190L), Component B(Catalyst) (18.5L)

2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Installation Instructions for an ASI Soundproof Door – High Definition version

    The wall that this was installed to was treated with products, too. You can view our video on Soundproofing a Wall (https://www.youtube.com/watch?v=rVtY6MZoFrY) for more information.

    https://www.acousticalsurfaces.com/acoustic_doors/soundproof_doors.htm

    Tools Needed:
    -Level
    -Pencil
    -Tape Measure
    -Utility Knife
    -Cordless Drill
    -Quart-Size Caulk Gun
    -Hammer
    -Installation Kit*
    -Installation Instructions*
    -Heavy Duty Screws*
    -Shims*
    -Backer Rod*
    -Acoustical Sealant*
    -Door Hardware Kit*
    -Door Casing (One installed on door when shipped, other side comes loose)*
    -Door & Jamb*

    *Included in Door Purchase (https://bit.ly/qZQjRh)

    Make sure to inspect the door and included items for any damage prior to installation.

    INSTALLATION INSTRUCTIONS
    1. Unscrew the temporary threshold on the bottom of the door.
    2. Determine which side of the jamb the hinges will be.
    3. Measure and mark hinge locations onto the door frame.
    4. Place a set of shims at each hinge, making sure they are plumb with the level.
    5. Tip the door into place, make sure all is plumb and level.
    6. Remove the two screws in the hinge closest to the door stop.
    7. Repeat for each hinge.
    8. Prop the bottom corner of the door with it swung at 90 degrees so that it holds the jamb tight to the drywall.
    9. Pre-drill the holes from the screws you just removed to prepare for the long screws. (We use a 5/32 bit)
    10. From top hinge down, install the included long screws.
    11. Adjust shims as necessary to ensure the door stays level.
    12. Shim the strike side of the door to get an even reveal on the inside of the door.
    13. Install the backer rod around the gap in the rough opening by pushing it in about an inch deep. You can use a shim to push it in.
    14. Fill the remaining gap with acoustical sealant.
    15. Remove the temporary brace off the bottom of the trim kit.
    16. Maintaining a 1/4″ reveal, attach the trim with the supplied screws.
    17. Nail trim to wall as needed.
    18. Fill holes with wood putty and sand.
    19. Remove the short hardware screws that came shipped from the strike side of the door.
    20. Replace them with the long screws for the strike hardware to secure the framing.
    21. Remove the trim on the hinge side of the door that shipped on the door.
    22. Repeat steps 13-18 on this side of the door.
    23. Install door hardware as specified.
    24. Ensure the door is shut and latched.
    25. Adjust the door seals by locating the Phillips screws on the face of the door seal and turn counter-clockwise to tighten the door seal. This will close the gap between the seal and the door.
    26. Work the way down the seal until all screws are adjusted so that the seal comes in contact with the door slab.
    27. Trim off excess gasket on the strike side of the door jamb at the bottom so that the gasket is flush with the floor.
    28. Adjust the bottom drop seal by loosening the set screw at the top of the drop seal counter-clockwise. When the screw engages the stop on the jamb, it will drop the seal down.
    29. Peel off the backer on the peel-and-stick seal cover panels and pressure fit over door seals. Start with the top and fit the sides into the miter.



    Water based finishes can be a little tricky to apply. They dry fast which means you have to apply them fast. Check out how I apply them in my bi-weekly finishing how-to video.

    If you enjoyed what you just watched, consider becoming a patron and support SimpleCove. https://www.patreon.com/simplecove

    Supplies used in this video (Affiliate links below help support this channel)
    Foam brushes: https://amzn.to/1OFwcmC
    Synthetic brush: https://amzn.to/1Reqo5z
    Minwax Polycrylic: https://amzn.to/1OFwkCA
    General Finishes Enduro-Var: https://amzn.to/1VRRVce

    Connect With SimpleCove:

    Website: https://www.simplecove.com
    Twitter: https://twitter.com/simplecove
    Facebook: https://facebook.com/simplecove
    Pinterest: https://www.pinterest.com/simplecove/
    Instagram: https://www.instagram.com/simplecoveshare

    Related Products

    WhatsApp Online Chat !