Manufacturer for Siway SV-602 Epoxy Structural Adhesive A/B to Jamaica Manufacturers

Manufacturer for Siway SV-602 Epoxy Structural Adhesive A/B to Jamaica Manufacturers
  • Manufacturer for Siway SV-602 Epoxy Structural Adhesive A/B to Jamaica ManufacturersManufacturer for Siway SV-602 Epoxy Structural Adhesive A/B to Jamaica Manufacturers

Short Description:

Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.   Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...


Product Detail

Attentions

Application

Product Tags

Our development depends on the advanced equipment, excellent talents and continuously strengthened technology forces. Manufacturer for Siway SV-602 Epoxy Structural Adhesive A/B to Jamaica Manufacturers, We appreciate your enquiry and it's our honor to work with every friend worldwide.


Description

SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.

 

Key Features

1. Room temperature curing Epoxy adhesive

2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)

3. Mix ratio of 1:1 by volume or by weight

4. Good mechanical property

5. Bonds a wide variety of building materials

6. Good waterproofing and chemical resistance

 

Basic Application

1, the external walls of stone material, ceramic and other hang bond;

2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;

3, concrete, stone and so on crack repair;

4, the structure of the localization, anchor, reinforcement and reinforcement.

 

Technical data sheet

The following data is for reference only and is not recommended for the specification

Shear strength Stainless steel-stainless steel/Standard conditions ≥18   JC887-2001
Pressure shear strength Stone-stone/ Standard conditions ≥12
Stone-stone/ The freeze-thaw cycle 50 times ≥10
Stone – stainless steel/ Standard conditions ≥12
Standard conditions:Temperature=23℃,relative humidity=50%,48 hours curing
attribute SV-602-A SV-602-B SV-602(After mixing)
Colour gray white grey
Density(g/cm³) 1.8 1.8 1.8
Viscosity(PaS) 200-400 150-250  
Effective operating time(23℃) N/A N/A 20min
           

 

Certification

JC 887-2001

 

Color

Part A-Grey Paste/Part B-White Paste

 

Package

9kg/9kg per unit and 15kg/15kg per unit

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • PVC flat roof repair – 28 years old Sarnafil PVC roof repaired with new IB PVC patches.



    How to install epoxy natural stone flooring
    Everlast pebblestone is very easy to install.
    Full instructions and tool list needed is here: https://www.everlastepoxy.com/pebblestone-river-rock/how-to-install
    The first step is to prepare the concrete by removing any existing coating. You can rent this floor maintainer at almost any tool rental location, this one is available at home depot for $34 for 4 hours.
    If you are removing a coating then get a coating removal attachment, for bare concrete use the concrete prep tool, for a plywood subfloor use 36 grit sandpaper.
    The next step is to prime the floor. Unless your floor has a moisture problem – then don’t prime the floor. Call us about our Vapor Vent system, a concrete moisture solution.
    For this project they used Everlast Outdoor Tough Weatherproof polyavastic because this epoxy natural stone flooring is exposed to sunlight and they want the floor to look nice for years. If they went with one of the UV resistant epoxies that other companies sell the protection would erode in a few months and the floor would turn yellowish and the finish would be chaulky. So they made the wise decision to use Everlast polyavastic and now their floor will look nice for years.
    The next step is to pour out all of one unit of part B into one can of part A and blend well and then roll on the primer. Cut the primer with solvent. If you are using our outdoor polyavastic cut it with MEK, if our indoor epoxy cut with xylene.
    Let the primer dry overnight.
    Mark out your first section on the floor so you can make sure your gauge rake is set to the proper depth and that you get the correct coverage. You may need to mark out the next section before blending each new batch until you are confident that you are getting the right coverage. This is a patio so we are doing 3 foot by 8 foot sections of 24 square feet for each batch. This gives us a depth of 1/2 an inch.
    Now you are ready to install the epoxy natural stone flooring. Pour out all of one unit of part B into one can of part A and blend well. Then pour 2 bags of pebbles into a $17 metal tub and pour the blended resin over the pebbles. Mix the resin in thoroughly with a mud mixing drill. Be sure to blend it thoroughly so that there are no dry patches of pebbles.
    Pour out the pebbles and spread them with the gauge rake to get a uniform coverage inside the 24 square foot section.
    Next even the pebbles out with a 16 inch finish trowel. We prefer the Marshalltown lightweight finish trowels. It is important to take your time and do a nice job. Try to have an even finish with no trowel marks or stray rocks sticking up. It is easy to do a nice job, but it does take extra time. If you try to hurry it will not look nice.
    If you leave uneven areas or holes while you are installing epoxy natural stone flooring then after the floor is finished some of the pebbles could start coming out in those areas. So the better of a job you do troweling, the less likely you will have to patch the floor area later on.
    The next step is to let the pebblestone get hard. Indoor epoxy will be cured the next morning. Outdoor polyavastic will take an extra day to cure.
    The next step is to scrape off any stray pebbles that are sticking up and sweep or blow off the floor to remove the extra pebbles. Then mix up some more polyavastic or epoxy and roll a topcoat over the floor.
    If you use an indoor epoxy topcoat it will be ready to walk on the next morning and the outdoor polyavastic topcoat will take an extra day to cure.
    Now you will have the nicest looking floor in town, so be prepared to offer your services to your friends and neighbors! Have fun and enjoy!
    To order your Everlast Pebblestone visit https://www.everlastepoxy.com/pebblestone-river-rock/natural-stone-flooring

    Related Products

    WhatsApp Online Chat !