Manufacturer for CV-709 silicone sealant for PV moudels Export to Malta

Manufacturer for
 CV-709 silicone sealant for PV moudels Export to Malta
  • Manufacturer for
 CV-709 silicone sealant for PV moudels Export to MaltaManufacturer for
 CV-709 silicone sealant for PV moudels Export to Malta
  • Manufacturer for
 CV-709 silicone sealant for PV moudels Export to MaltaManufacturer for
 CV-709 silicone sealant for PV moudels Export to Malta
  • Manufacturer for
 CV-709 silicone sealant for PV moudels Export to MaltaManufacturer for
 CV-709 silicone sealant for PV moudels Export to Malta

Short Description:

Description CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949   Key Features 1. 100% silicone 2. No sag 3. high thixotropy 4. Water & weatherproof 5. For solar components involved in the base material has good bonding   Basic Ap...


Product Detail

Attentions

Application

Product Tags

Our goal is to satisfy our customers by offering golden service, good price and high quality for Manufacturer for CV-709 silicone sealant for PV moudels Export to Malta, We welcome new and old customers from all walks of life to contact us for future business relationships and mutual success.


Description

CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949

 

Key Features

1. 100% silicone

2. No sag

3. high thixotropy

4. Water & weatherproof

5. For solar components involved in the base material has good bonding

 

Basic Application

1.Solar module frame seal

2.The adhesive of the solar energy back to the terminal block

3.General industrial assembly with seal

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
  specific gravity g/ml 1.34-1.40
GB13477 Operating time min 15
GB13477 surface drying time(25℃,50%R.H.) min 40-60
3 days after curing——25℃,50%R.H.
  Temperature range -55~200
GB13477 Durometer Hardness Shore A 40~55
  The ultimate tensile strength Mpa ≥2
GB13477 Breaking elongation % 300-600
  Aluminum bonding shear strength Mpa ≥1.5
Electrical properties
  Breakdown voltage Kv/mm ≥20
  Volume resistance ohm.cm 9E+14
  Dielectric constant   3.1@50Hz

 

Certification

UL E339949; TUV

 

Color

Black, White

 

Package

300ml in cartridge * 24 per box, 500ml in sausage *20 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Tired of boring drink coasters? Let’s design our own with just a few simple supplies. You will need a picture, some tiles, mod podge, felt and a brush!
    Email List Signup: https://householdhacker.tv/list

    Full Instructions:
    To pull this off we need a few basic items… a cutting board or scissors… Some mod lodge glue and sealant. a brush, some ceramic tiles and some felt.

    If you want a custom design print out a couple color pictures but leave enough room for about 4 and a half inches each. A standard piece of paper can hold a couple of these.

    We are using a standard 4×4 ceramic tile. These can be purchased at the hardware store for about 18 cents each!

    Print out your design and lets cut it up! You want to make a square that is 4 and 1/8th inches on all sides.

    Once you cut it up place it on the tile to make sure the measurements were correct. You want a little bit of white as a border.

    Now grab some mod lodge and apply a thin coat directly on to the tile. In a pinch you could use elmers glue but the top layer will not be as clean and good looking.

    At this point it’s good to mention that you don’t have to print anything, you can cut logos or pictures out of a magazine or old book to make your awesome coasters however you want… just follow the same process as before.

    Once the image is centered and secured into place. Apply a first top coat to the picture. Go slowly and steady here to avoid bubbles in the paper. Make a nice thin and straight layer and then give it at least 10 minutes to dry.

    After you have applied about 3 layers, you should have a nice water proof and flush looking coaster. It’s time to pad the bottom with felt to finish up the project.

    Get your felt out which can be purchased at any art store and cut it to the same size at the paper… That’s 4 1/8 inches on all sides. Now apply another thin layer of mod lodge or glue to the bottom and carefully place the felt into position.

    And that’s it! Once this process is completed, let everything dry for about an hour and they are ready for use! These things make great gifts for anyone.

    -~-~~-~~~-~~-~-
    NEWEST VIDEO: 10 Ways To Reuse Soda Cans In Your Home

    -~-~~-~~~-~~-~-

    Related Products

    WhatsApp Online Chat !