Lowest Price for SV-999 Structural Glazing Silicone Sealant to London Factory

Lowest Price for SV-999 Structural Glazing Silicone Sealant to London Factory
  • Lowest Price for SV-999 Structural Glazing Silicone Sealant to London FactoryLowest Price for SV-999 Structural Glazing Silicone Sealant to London Factory
  • Lowest Price for SV-999 Structural Glazing Silicone Sealant to London FactoryLowest Price for SV-999 Structural Glazing Silicone Sealant to London Factory
  • Lowest Price for SV-999 Structural Glazing Silicone Sealant to London FactoryLowest Price for SV-999 Structural Glazing Silicone Sealant to London Factory

Short Description:

Description SV – 999 silicone structural sealant is a one-component, neutral curing, designed for glass curtain wall, aluminum curtain wall, glass daylighting roof and metal structural engineering structural assembly silicone sealant. Show the effective physical properties and bonding performance   Key Features 1. 100% silicone 2. No sag 3. Strong bonding strength 4. Water & weatherproof 5. Primerless adhesion to most building materials 6. 25% movement capability   Basic Application...


Product Detail

Attentions

Application

Product Tags

We are committed to providing easy,time-saving and money-saving one-stop purchasing service of consumer for Lowest Price for SV-999 Structural Glazing Silicone Sealant to London Factory, We welcome customers, business associations and friends from all parts of the world to contact us and seek cooperation for mutual benefits.


Description

SV – 999 silicone structural sealant is a one-component, neutral curing, designed for glass curtain wall, aluminum curtain wall, glass daylighting roof and metal structural engineering structural assembly silicone sealant. Show the effective physical properties and bonding performance

 

Key Features

1. 100% silicone

2. No sag

3. Strong bonding strength

4. Water & weatherproof

5. Primerless adhesion to most building materials

6. 25% movement capability

 

Basic Application

1.Glass curtain wall, aluminum curtain wall structure adhesive seal

2.Glass daylighting roof, metal structure engineering

3.Insulating glass bonding

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
  specific gravity g/ml 1.40
GB13477 Flow, sagging   or vertical flow mm 0
GB13477 Operating time min 15
GB13477 surface drying time(25℃,50%R.H.) min 40-60
Sealant curing speed and operating time   will have different with different temperatures and temperature, high   temperature and high humidity can make sealant curing speed faster, rather   low temperature and low humidity are slower.21 days after   curing——25℃,50%R.H.
GB13477 Durometer Hardness Shore A 40
  The ultimate   tensile strength Mpa 1.3
GB13477 Tensile strength(23℃) Mpa 0.8
GB13477 Tensile strength(90℃) Mpa 0.5
GB13477 Tensile strength(-30℃) Mpa 0.9
GB13477 Tensile strength(flooding) Mpa 0.6
GB13477 Tensile strength(flooding   – ultraviolet) Mpa 0.6

 

Certification

GB 16776;ASTM C1184

 

Color

Black

 

Package

300ml in cartridge * 24 per box, 500ml in sausage *20 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

 

  • Previous:
  • Next:



  • 360FC FAST CURE PUR WOOD GLUE D4

    Akfix 360FC is a one-component, fast curing liquid polyurethane adhesive. It possesses high water
    resistance and bonding strength.

    PROPERTIES
    * Easy application, low viscosity
    * High bond strength
    * Fast Curing
    * Water resistant (D4-DIN EN204)
    * Can be used on slightly humid surfaces
    * Resistant to temperature extremes
    * Resistant to moisture and chemicals



    Corner detail – Fixing where drywall ties into the log, log corners, exterior saddles anywhere there are openings.

    Finishing log home corners with caulk is simple following these instructions.

    TRANSCRIPT:
    Hi, my name is Scott, with Weatherall Company, and I’m going to quickly cover how you handle a corner detail. This is an example of where drywall ties into the logs. What I’m doing here can be used where you have log corners, log saddles on the exterior, doing any type of corner detail.

    So first, if I have openings like that you see here, I need to throw a little bit of backer rod in there. It’s fairly simple to do. Just quickly cut off … I usually find bits of scraps of backer rod lying around, and I put them in there, make sure they’re flush. That piece right there might need a piece of round backer rod, and I will put that in there. A lot of times I will carry around just kind of a dull, heavy chisel, and that will help, usually just help push stuff in there.

    Now that is actually fine and we’re good to go, but any area where it opens up, probably more than a quarter of an inch, you’re going to want to fill. Same goes for the logs. If the logs are cut back from the drywall, you’re going to want to cut a piece, fill it, make sure it’s flush, and then we’ll go ahead and chink it.

    I am using my Albion caulking gun for this, with a half inch nozzle. That helps provide the best detail for these joints. You don’t need to go over a half inch. I see some people put large pieces of backer rod and they will chink that to about the same width of their horizontal joints and that is overkill. It’s probably not the best joint design. It’s much easier and better just to go with the smaller tip. I wouldn’t go under a half inch. I wouldn’t do a quarter or an eighth inch of material.

    It really is about this simple. Nice thing about this gun is I can move it around, I can go upside down with it. Again, I’ve got a 45 degree tip and I’m trying to keep that tip perpendicular to my work surface, and try and put that stuff in there as perfect as I can because it just makes for finishing a lot easier. And it should really just go about this quick. Really, not that difficult.

    Usually right about here I will stop, release the pressure on the gun, and start from the bottom. I have better control over the gun that way. I try to keep the material as flat as I can. If I hold the gun up like this, I get the material too thick. It’s going to be a lot harder to trowel. If I can keep that tip flat, it can be a lot easier to finish the material.

    Once you get used to it, it goes fairly fast. Shouldn’t take a whole heck of a lot of time to do these joints. A lot of times they just blend right in with the drywall. Now, we’ll usually go right over the molding. See how this molding is scribed into the log? We’ll cover that as well.

    And then to trowel it, I usually just use my finger. And if you’ve done a good enough job applying it, you don’t really have to fiddle with it for too much. I usually just spray a little on the material and just go right over the top of it. All you’re doing is just gently seating the material against the log.

    Related Products

    WhatsApp Online Chat !