Hot Selling for CV-709 silicone sealant for PV moudels to Rwanda Factory
Short Description:
Description CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949 Key Features 1. 100% silicone 2. No sag 3. high thixotropy 4. Water & weatherproof 5. For solar components involved in the base material has good bonding Basic Ap...
We have the most advanced production equipment, experienced and qualified engineers and workers, recognized quality control systems and a friendly professional sales team pre/after-sales support for Hot Selling for CV-709 silicone sealant for PV moudels to Rwanda Factory, Welcome any inquiry to our company. We will be glad to establish friendly business relationships with you!
Description
CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949
Key Features
1. 100% silicone
2. No sag
3. high thixotropy
4. Water & weatherproof
5. For solar components involved in the base material has good bonding
Basic Application
1.Solar module frame seal
2.The adhesive of the solar energy back to the terminal block
3.General industrial assembly with seal
Technical data sheet
Test standard | Test project | Unit | value |
Before curing——25℃,50%R.H. | |||
specific gravity | g/ml | 1.34-1.40 | |
GB13477 | Operating time | min | 15 |
GB13477 | surface drying time(25℃,50%R.H.) | min | 40-60 |
3 days after curing——25℃,50%R.H. | |||
Temperature range | ℃ | -55~200 | |
GB13477 | Durometer Hardness | Shore A | 40~55 |
The ultimate tensile strength | Mpa | ≥2 | |
GB13477 | Breaking elongation | % | 300-600 |
Aluminum bonding shear strength | Mpa | ≥1.5 | |
Electrical properties | |||
Breakdown voltage | Kv/mm | ≥20 | |
Volume resistance | ohm.cm | 9E+14 | |
Dielectric constant | 3.1@50Hz |
Certification
UL E339949; TUV
Color
Black, White
Package
300ml in cartridge * 24 per box, 500ml in sausage *20 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
LINK TO PART 2: https://www.youtube.com/watch?v=dyBhd66lY9I
If you know your top is not leaking, or if you have replaced your top and the roof is still leaking, here is a DEFINITE FIX. DETAILS BELOW.
1) Take out rear seat: 2 push-pins you need to push to release bottom of rear seat, each are under the middle of each seat. Put your fingers between the carpet and the seat and feel around, push the button in, and release seats.
2) Take out rear back-rest. 2 bolts with a ratchet in plain view. Then, when unbolted, push back-rest UPWARDS to unhook hinges that are near the top of the back rest, then pull out.
3) Remove plastic side-panel. When you open the door, that piece of plastic above where it says Mustang, needs to be removed so you can access more of the carpet to pull it up. Just pull it up with a trim-removal tool.
4) Use a Torx-45 (pretty sure) to remove your FRONT seat belt bolts. DO NOT turn the wrong way, make sure youre pushing the wrench towards the ground, not pulling it up or you’ll snap the bolt and then your DIY career ends. The bolt needs to turn LEFT!
4) Remove Seats. Straight forward, 4 bolts, simple ratchet. Motor assembly wires for driver’s seat just unclip easily.
5) Peel carpet as FAR to the middle as possible so you can see the entire weld covered in factory sealant from FRONT TO BACK.
6) Seal with whatever urethane, rubber, other sealant you or a professional have chosen SPECIFICALLY for TEMPERATURE RESISTANCE, WATER RESISTANCE AND FLEXIBILITY.
7) LET DRY!!!
***DUCT TAPE LINK FIX I TALKED ABOUT IN THE VIDEO https://www.youtube.com/watch?v=C21EcaTRefQ *********