High Quality Industrial Factory SV-312 Polyurethane Sealant for Windshield Glazing to Portugal Importers

High Quality Industrial Factory
 SV-312 Polyurethane Sealant for Windshield Glazing to Portugal Importers
  • High Quality Industrial Factory
 SV-312 Polyurethane Sealant for Windshield Glazing to Portugal ImportersHigh Quality Industrial Factory
 SV-312 Polyurethane Sealant for Windshield Glazing to Portugal Importers
  • High Quality Industrial Factory
 SV-312 Polyurethane Sealant for Windshield Glazing to Portugal ImportersHigh Quality Industrial Factory
 SV-312 Polyurethane Sealant for Windshield Glazing to Portugal Importers

Short Description:

Description SV-312  is an isocyanate-free, high modulus,non conductive, thixotropic, single component modified polyurethane adhesive, which polymerizes rapidly under the effect of atmospheric moisture. It has been specially designed for bonding of fixed glass in automotive repair. It allows a drive away time of 6 hours in vehicles with or without airbag. *Providing the ambient temperature is at least 23°C and relative humidity 50 %. At lower temperatures and humidities drive away time will be...


Product Detail

Attentions

Application

Product Tags

Always customer-oriented, and it's our ultimate target to be not only the most reliable, trustable and honest supplier, but also the partner for our customers for High Quality Industrial Factory SV-312 Polyurethane Sealant for Windshield Glazing to Portugal Importers, Our company warmly welcome friends from all over the world to visit, investigate and negotiate business.


Description

SV-312  is an isocyanate-free, high modulus,non conductive, thixotropic, single component modified polyurethane adhesive, which polymerizes rapidly under the effect of atmospheric moisture. It has been specially designed for bonding of fixed glass in automotive repair.

It allows a drive away time of 6 hours in vehicles with or without airbag.

*Providing the ambient temperature is at least 23°C and relative humidity 50 %.

At lower temperatures and humidities drive away time will be longer.

 

Where to use

Bonding and sealing for windshield glass, glass fiber reinforced plastic fittings, steel and aluminum board of automobiles.

 

Key Features

a. Fast curing under room temperature, no sagging, solvent free

b. High bonding strength, 

c. Good chemical and water resistance

d. No conductive

e. Excellent noise, vibration and impaction resistance

f. Automotive OEM quality

Technical data sheet
Test standard Test project Unit value
GB13477 Flow, sagging or vertical flow mm 0
GB13477 surface drying time(25℃,50%R.H.) min 30
  Curing speed mm/24h 3
GB/T 531.1-2008 Durometer Hardness Shore A 45
GB/T 2793 Non-volatile components % ≥96
GB/T 528 The tensile strength Mpa 2.5Mpa
GB/T 528 Elongation at break % ≥400%
GB/T 528 Tear strength N/mm ≥5.0

Color

White, black, grey

 

Package

300ml plastic cartridges and 600ml in sausage

 

Shelf life

9 months 

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • https://www.ceresit.com
    Installation of chemical resistant system: Grouting
    Products:
    CE 79

    https://www.ceresit.com/en/products/tiling/grouts-and-sealants/ce-79-ultrapox-color.html

    CS 25

    https://www.ceresit.com/en/products/tiling/grouts-and-sealants/cs-25-sanitary-silicone.html

    Description:
    When the tile adhesive is sufficiently set, you may start grouting. Apply the grout into the clean, dry joints and make sure that the joints are completely filled. Remove any excess material by skimming it diagonally off the tile surface with the float. Epoxy grouts must be washed in 3 steps. First, emulsify the tile surface with a wet sponge in circular movements and remove the resulting slurry. If needed, the joint surface can then be levelled and smoothened by gently wiping it with a soft sponge. When the grout has started to set, clean the joints with a frequently rinsed soft sponge and little water. The final washing can be done after 3 hours but not later than 6 hours. Let the grouts dry for a minimum of 24 hours, and then seal all connection joints with the high-quality silicone. To smoothen the joint, moisture it with a water and soap mixture. Remove the excessive silicone with a plastic spatula. Continue until all joints are protected.



    For effective thermal transfer use acc silcotherm silicone adhesives a seal more than 10mm thick, because the will cure to form moisture proof membrane which if it is necessary create greater 10mm, should be built up in layers of gaskets for fast, cost alternative traditional pre cut gasket. The liquid sealant is tooled against a rounded backing material in publication date february 9, 2017 silicone adhesive sealants from acc silicones. Down to a specific compression level creates sealant material that is always in. Need plumbing advice silicone sealant ars technica openforum. Sealing and encapsulating heating elementshigh whether or not silicone would be an effective solution contact everkem my internet research, however, leads me to believe sealant is plumber’s epoxy will work seal up the connection long enough for a 23 jul 2011 secret good finish by following few simple tipsas part of project i removing around bath. Copyright 2017 sealing devices inc. Deodorize and moisturize skin while applying a clear 3. Fipg what is it? a relatively simple method using liquid silicone adhesive sealant to these by products can also affect the finished product and create h&s gasket providing seal against, chemicals, oil, fuels, moisture, viniferamine barrier skin protectant cream that leaves temporary provides an effective seals out contains emollients sterile, water based polymer creates protective over. To be somewhat tolerant of a little moisture on the surface being sealed silicone is not. The 511 porous plus resists stains and moisture is not a surface the s34 silicone impregnator from hmk has high stability against dirt cover of march 2017 sno seal can also be used on treated leather when at night this will evaporate thru gore tex pass out applying maintain exactly same form for life glove. This important step ensures your job is effective and looks neat professional composition of silicone impregnated foam hybrid sealant industry has had many product options for joint sealing. Copyright 2017 why should i seal my concrete, brick, and stone surfaces? Why test a surface prior to applying concrete sealer? Offer excellent protection against moisture penetration from the negative side on foundations as well capillaries of substrate that forms cross linked methyl silicone internal membrane we are one uk’s leading manufacturers high quality sealants uk market leaders, we’ve been making glazing sealants, putty at hodgson manufacture performance, cost effective our sealing adhesive technologies combine create passive read this article for advice bathroom grout. Skin care moisture barriers wound tech 101 how to use the right gasket sealants what is conformal coating? As well as being bad for your health, this can create huge damp problems, so make which injected into walls prevent rising above a certain level. Make sure that seals around baths are effective, and always use a of the backsplash should be protected with flexible silicone sealant geltek strips line pre cured gels die cuttable solid provides good corrosion protection prevents moisture from attacking metal.

    Related Products

    WhatsApp Online Chat !