High quality factory SV-8800 Silicone Sealant for Insulating Glass for European Importers

High quality factory SV-8800 Silicone Sealant for Insulating Glass for European Importers
  • High quality factory SV-8800 Silicone Sealant for Insulating Glass for European ImportersHigh quality factory SV-8800 Silicone Sealant for Insulating Glass for European Importers
  • High quality factory SV-8800 Silicone Sealant for Insulating Glass for European ImportersHigh quality factory SV-8800 Silicone Sealant for Insulating Glass for European Importers
  • High quality factory SV-8800 Silicone Sealant for Insulating Glass for European ImportersHigh quality factory SV-8800 Silicone Sealant for Insulating Glass for European Importers

Short Description:

Description SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.   Where to use It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.   Key Features 1. High Modulus 2. UV resistance 3. Low vapor and gas transmission 4. Primerless adhesion...


Product Detail

Attentions

Application

Product Tags

We are committed to providing easy,time-saving and money-saving one-stop purchasing service of consumer for High quality factory SV-8800 Silicone Sealant for Insulating Glass for European Importers, We warmly welcome all perspective inquiries from home and abroad to cooperate with us, and look forward to your correspondence.


Description

SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.

 

Where to use

It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.

 

Key Features

1. High Modulus

2. UV resistance

3. Low vapor and gas transmission

4. Primerless adhesion to coated glass

5. 100% compatible to SV-8890

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 Specific gravity(After mixing)   1.33
GB13477 Operating time min 20-40
GB13477 surface drying time(25℃,50%R.H.) min 80-188
corrosivity     No
7 days after curing——25℃,50%R.H.
GB/T 531 Durometer Hardness Shore A 40
GB13477 The tensile modulus at 12.5% elongation Mpa 0.18
  The ultimate tensile strength Mpa 0.92
GB13477 Elongation limit (fracture) % 150

 

Certification

GB-24266-2009;

 

Color

Component A(Base) – White, Component B(Catalyst)- Black

 

Package

1. Component A(Base): (190L), Component B(Catalyst) (18.5L)

2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • I was interested in buying this Jenvey inlet manifold but as with most things I prefer to have a look and see if there’s any videos relating to it so I can get a better idea as to what I’m buying, I was surprised to find that there wasn’t really any about the manifold/plenum but more about the Jenvey throttle bodies so I decided to make one in hope that it will help other people make the decision as weather or not to buy one.
    I was really impressed with the workmanship of this product and although its expensive I wouldn’t say its unaffordable for most people as the way its made you could buy everything individually when the money is available.

    This Plenum/manifold comes in multiple configurations and there’s more than likely a manifolds that the plenum bolts too so you can install one to your car too.
    This one is fitted to My ford focus, 2.0l zetec turbo engine and the only problems I can across is that the head temp sensor got in the way but seeing as i’m using Omex 600 management I didn’t need it so was easy enough to remove, however it was only just in the way and I think if I was to have tightened the sensor a little more it would have cleared it.
    The second problem I had was the throttle body was a bit too close to the fuse box, I may have been able to find a silicone coupler tight enough to clear it but I made a stainless steel adapter instead to move the throttle body out the way which I think worked well.
    I spoke to the guys at Jenvey multiple times and found them all very helpful and knowledgeable and Ill certainly be using them again in the future.
    As to how much power this made I’m afraid I cant answer that, I’ve been building this car for years and am yet to finish it so unfortunately am unable to provide you with a before and after.

    When assembling this manifold I used a high heat resistant sealant, see link below, this is a step you may or may not want to do but I felt it would add a greater seal and give me a little peace of mind when ramping the boost up, the kit does come supplied with O-ring gaskets which I also used so the sealant is a step that you choose not to do and more than likely still have the manifold perform perfectly.

    Link to Jenvey’s website:

    https://www.jenvey.co.uk/

    Link to the Zetec kit:

    https://www.jenvey.co.uk/products2/throttle-body-kits/zetec-turbo-kit-ckfd02t

    Find the manifold for your car:

    https://www.jenvey.co.uk/products2/manifold

    Sealant used:

    https://www.amazon.co.uk/d/DIY-Tools/Silicone-Sealant-High-Temperature-300c-Silcoset-158/B003N1Y7OS/ref=sr_1_2/260-5667292-4899156?ie=UTF8&qid=1497165680&sr=8-2&keywords=silcoset+158

    Thread Lock:

    https://www.amazon.co.uk/Loctite-Lock-Acting-Thread-Sealant/dp/B003ZUXQIA/ref=sr_1_1?ie=UTF8&qid=1497165745&sr=8-1&keywords=loctite

    Thinners for cleaning:

    https://www.amazon.co.uk/CarPlan-STT005-Standard-Thinner/dp/B006CH5DV6/ref=sr_1_4?ie=UTF8&qid=1497165841&sr=8-4&keywords=paint+thinners

    Music: https://www.bensound.com

    Thankyou for watching, I tried to include as much information as possible so you could decide if this is the manifold for you.
    I’ll try and record anything else I do that I feel is of interest so if you enjoyed this video please like it and subscribe.



    SU 10 is a high performance, UV stable, single component, moisture curing polyurethane sealant. It has good recovery properties and suitable for sealing …

    Related Products

    WhatsApp Online Chat !