Free sample for SV-8800 Silicone Sealant for Insulating Glass for Haiti Factory

Free sample for
 SV-8800 Silicone Sealant for Insulating Glass for Haiti Factory
  • Free sample for
 SV-8800 Silicone Sealant for Insulating Glass for Haiti FactoryFree sample for
 SV-8800 Silicone Sealant for Insulating Glass for Haiti Factory
  • Free sample for
 SV-8800 Silicone Sealant for Insulating Glass for Haiti FactoryFree sample for
 SV-8800 Silicone Sealant for Insulating Glass for Haiti Factory
  • Free sample for
 SV-8800 Silicone Sealant for Insulating Glass for Haiti FactoryFree sample for
 SV-8800 Silicone Sealant for Insulating Glass for Haiti Factory

Short Description:

Description SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.   Where to use It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.   Key Features 1. High Modulus 2. UV resistance 3. Low vapor and gas transmission 4. Primerless adhesion...


Product Detail

Attentions

Application

Product Tags

We keep improving and perfecting our products and service. At the same time, we work actively to do research and development for Free sample for SV-8800 Silicone Sealant for Insulating Glass for Haiti Factory, We always hold the philosophy of win-win, and build long-term cooperation relationship with customers from around the world.We believe that our growth base on customer's success, credit is our life.


Description

SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.

 

Where to use

It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.

 

Key Features

1. High Modulus

2. UV resistance

3. Low vapor and gas transmission

4. Primerless adhesion to coated glass

5. 100% compatible to SV-8890

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 Specific gravity(After mixing)   1.33
GB13477 Operating time min 20-40
GB13477 surface drying time(25℃,50%R.H.) min 80-188
corrosivity     No
7 days after curing——25℃,50%R.H.
GB/T 531 Durometer Hardness Shore A 40
GB13477 The tensile modulus at 12.5% elongation Mpa 0.18
  The ultimate tensile strength Mpa 0.92
GB13477 Elongation limit (fracture) % 150

 

Certification

GB-24266-2009;

 

Color

Component A(Base) – White, Component B(Catalyst)- Black

 

Package

1. Component A(Base): (190L), Component B(Catalyst) (18.5L)

2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • How to install Oceanside paper faced Glass Mosaic tile on a kitchen backsplash.
    Paper faced mosaic glass tile requires an installation method that has a few more steps that would normally be used compared to other types of mosaic tile. This is especially true if the mosaic glass tile is transparent. First it is important to use the correct setting material to install glass tile. Glass tile should never be installed using mastic. The type of thinset needed to install glass tile is one that is white and has a high polymer content. I usually use “Tec Superflex”. It is also important that the thinset used is one that has the same color across multiple units, to insure color consistency when installing large projects that require more than one bag of thinset. Using a lower quality thinset can cause variation in color and shading of the glass tile, and also result in tiles not adhering to the mortar. Paper faced tiles like the Oceanside mosaic tile used in this video are usually very thin so oozing of the thinset between the tiles can be a problem if the correct trowel is not used to spread the thinset. Despite this one hundred percent coverage must be achieved on the back of the tile to obtain a proper installation. If 100% coverage is not achieved, visible color shading will be present throughout the tile installation which will create an unpleasant final product. In this case I used a 3/16″th V-Notched trowel. The thinset is first spread on the wall with the notched side of the trowel in such a way that the lines left by the trowel are all even in depth and uniformly going in the same direction. Once this is achieved, the flat side of the trowel is used to “Knock” down the ridges and create a flat even bed of mortar, but at the same time not removing any of the thinset from the wall. The next step is to start setting the tiles in the prepared thinset by placing the tiles on the wall a sheet at a time, aligning the grout lines between sheets. Once a number of sheets have been placed then it is time to “Beat them in” this is done by placing a flat piece of wood, such as a small segment of 2×4, on the tile and then gently tapping the wood with a hammer so as to set the mosaic tile into the thinset until 100% coverage is achieved. Do not use a rubber float to beat in the tile. Let the tile “Set” for a period of time, 30 minutes more or less. Once this time period has elapsed it is time to start wetting the paper for removal. This will probably take 5 to 10 minutes and require that you wet the surface of the paper several times. When the paper has loosened start pealing it off the tile, do not wait until the next day to do this, remove the paper while the thinset is still fresh. This will allow for necessary adjustments to individual tiles. Continue this process until the installation of the tile is complete. Allow the tile to set, all residue of the paper adhesive should be removed before grouting. Determine whether sanded or unsanded grout should be used, in this case sanded grout was needed. Some glass mosaic tile require that they be sealed before grouting, this particular tile did not call for sealing. The proceeding is intended as a guide line and not complete instructions on how to install mosaic glass tile, complete installation instructions are usually supplied with the tile at the time of purchase, or may be included in the tile packaging.
    This Oceanside mosaic glass tile backsplash was installed by Sal DiBlasi, Elite-Tile Company in Boston’s North Shore.
    All tile installed by Sal DiBlasi, Elite-tile Company, in the Boston North Shore area
    Youtube Channel https://www.youtube.com/user/saldibs?feature=watch
    Facebook https://www.facebook.com/pages/Elite-Tile-Company/56681633342
    Website https://www.elitetileco.com/
    Twitter

    https://twitter.com/saldiblasi1



    In this tutorial we mold an original clay sculpt with PlatSil 71-11 silicone. This is the basic method for making a simple block mold of an original sculpt. The sculpture we molded was created by my daughter, Renee, using Protolina Grey-Green clay. For the record, all of our clays are sulfur free on our webstore, so there we have greatly reduced the danger of contamination.
    BITY Instagram: @bitymoldsupply

    The volume equation we used to calculate the rubber used for this mold is on page 14 of the Polytek catalog: https://cdn.shopify.com/s/files/1/1344/1323/files/polytekcatalog.pdf?12902152489646789087
    Protolina Grey-Green Clay: https://www.brickintheyard.com/collections/clays-for-sculpting-mold-making
    Pol-Ease 2500 release: https://www.brickintheyard.com/collections/releases
    PlatSil 71-11: https://www.brickintheyard.com/collections/tinsil-platsil-silicones
    EasyFlo 60 Resin: https://www.brickintheyard.com/collections/casting-rubber

    Related Products

    WhatsApp Online Chat !