Free sample for CV-709 silicone sealant for PV moudels for Costa Rica Manufacturer

Free sample for CV-709 silicone sealant for PV moudels for Costa Rica Manufacturer
  • Free sample for CV-709 silicone sealant for PV moudels for Costa Rica ManufacturerFree sample for CV-709 silicone sealant for PV moudels for Costa Rica Manufacturer
  • Free sample for CV-709 silicone sealant for PV moudels for Costa Rica ManufacturerFree sample for CV-709 silicone sealant for PV moudels for Costa Rica Manufacturer
  • Free sample for CV-709 silicone sealant for PV moudels for Costa Rica ManufacturerFree sample for CV-709 silicone sealant for PV moudels for Costa Rica Manufacturer

Short Description:

Description CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949   Key Features 1. 100% silicone 2. No sag 3. high thixotropy 4. Water & weatherproof 5. For solar components involved in the base material has good bonding   Basic Ap...


Product Detail

Attentions

Application

Product Tags

we can offer high quality products, competitive price and best customer service. Our destination is "You come here with difficulty and we give you a smile to take away" for Free sample for CV-709 silicone sealant for PV moudels for Costa Rica Manufacturer, We sincerely welcome overseas customers to consult for the long-term cooperation and the mutual development.


Description

CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949

 

Key Features

1. 100% silicone

2. No sag

3. high thixotropy

4. Water & weatherproof

5. For solar components involved in the base material has good bonding

 

Basic Application

1.Solar module frame seal

2.The adhesive of the solar energy back to the terminal block

3.General industrial assembly with seal

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
  specific gravity g/ml 1.34-1.40
GB13477 Operating time min 15
GB13477 surface drying time(25℃,50%R.H.) min 40-60
3 days after curing——25℃,50%R.H.
  Temperature range -55~200
GB13477 Durometer Hardness Shore A 40~55
  The ultimate tensile strength Mpa ≥2
GB13477 Breaking elongation % 300-600
  Aluminum bonding shear strength Mpa ≥1.5
Electrical properties
  Breakdown voltage Kv/mm ≥20
  Volume resistance ohm.cm 9E+14
  Dielectric constant   3.1@50Hz

 

Certification

UL E339949; TUV

 

Color

Black, White

 

Package

300ml in cartridge * 24 per box, 500ml in sausage *20 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • https://www.ceresit.com
    FOUNDATION WATERPROOFING – against ground moisture and water
    Ceresit offers complete systems for every kind of waterproofing.
    Chosen product and application method should depend on construction’s type, water load and requirements of the country.
    CERESIT WATERPROOFING MEMBRANE SYSTEM
    Bituminous self-adhesive membrane system against ground moisture and water

    1,SUBSTRATE PREPARATION

    Before application of the waterproofing materials check if the substrate is dry, even, compact, stable, free of dust and laitance.
    CX 5 Rapid cement

    https://www.ceresit.com/en/products/mortars—auxiliaries/fast-setting-and-grouting-mortars/cx-5-rapid-cement.html

    CX 20INSTALLATION AND REPARATION MORTAR
    Any damage at the substrate should be filled in and levelled with e.g. cementitious mortar. Chamfer all edges at an angle of less than 450.
    Get rid of any substances which decrease adhesion.
    To remove all loose particles and laitance from the substrate use the grinding machine or steel brush.
    Remove the dust properly to prepare the surface for priming.

    2, PRIMER APPLICATION

    At temperatures lower than +50C (down to 00C), use BT 26 primer undiluted.Mix BT 26 Primer carefully with water at a ratio of 1:1 parts by volume.The diluted primer can be used at temperatures above +50C.
    BT 26 “ALL-WEATHER” PRIMER

    https://www.ceresit.com/en/products/waterproofing/balconies-terraces-patios/bitumen-membrane-products/bt-26-all-weather-primer.html

    Use a brush to apply a generous and uniform coat.In the case of coarse-pored surfaces, e.g. pumice and hollow blocks as well as aerated concrete.The primer must always be used undiluted.
    Check if the priming coat is completely dry!
    The drying time depends on the climate conditions and type of substrate.
    BT 18 SELF-ADHESIVE WATERPROOFING MEMBRANE

    https://www.ceresit.com/en/products/waterproofing/balconies-terraces-patios/bitumen-membrane-products/bt-18-self-adhesive-waterproofing-membrane.html

    BT 21 “ALL-WEATHER” WATERPROOFING MEMBRANE

    https://www.ceresit.com/en/products/waterproofing/balconies-terraces-patios/bitumen-membrane-products/bt-21-all-weather-sealing-membrane.html

    Check the adhesion of the membrane to the substrate.Take a membrane strip of 20 cm length and press half of it to the wall.Then try to pull it off. If the primer comes off the substrate, adhesion is not yet sufficient.Adhesion is sufficient if the membrane can only forcibly be removed from the substrate.

    3, MEMBRANE APPLICATION

    - Securing corners
    It is very important to install a separate protection of inner and outer corners.These areas are especially endanger with water and moisture.Membrane elements of adequate shape and size should be previously prepared.For faster working progress you can use prefabricated inner and outer corner elements (CA 25 and CA 26).
    CA 25 / CA 26 PREFABRICATED PVC FOUNDATION CORNERS FOR WATERPROOFING

    https://www.ceresit.com/en/products/waterproofing/balconies-terraces-patios/bitumen-membrane-products/ca-25-ca-26-internal-external-corner.html

    These elements can be fixed on the priming coat with adhesive or sealant, e.g. FT 101 or BT 40.
    FT 101 FLEXTEC® SEALING COMPOUND WITH FLEXTEC® TECHNOLOGY

    https://www.ceresit.com/en/products/tiling/grouts-and-sealants/ft-101-flextec.html

    BT 40 EXPANDING PU ADHESIVE FOAM
    After that membrane should be put according to the installation instruction.In case of pipe penetrations consider the following working steps:
    Grind the surface of the pipe with a grinding paper or steel brush to ensure good adhesion.Clean the surface thoroughly.Prepare elements cutted from the membrane to fix the collar around the pipe.Use knife handle or similar to press the membrane correctly.Apply one additional strip of the membrane to secure the edge of the isolation.Cut the BT 21 to the required length, roll it up, remove the backing paper and fix it to the wall in vertical orientation and with an overlapping of 10 cm.Before fixing to the top make sure that the membrane is in horizontal / vertical orientation.The top edge of the membrane should be additionally protected.
    CA 23 ALUMINIUM FIXING TAPE
    BT 21 / BT 18 have to be protected against damage by a protective layer, e.g. polystyrene / PU boards.asure the dimensions and cut the boards precisely to a shape.

    4, APPLICATION OF PROTECTIVE & INSULATION LAYER
    For fixing EPS boards to the membrane bitumen sealant or PU foam can be used.Apply strips of the foam on the boards, wait few seconds and press the boards to the wall.After finishing the insulation work the excavation should be refilled.

    Ceresit
    Quality for professionals
    Henkel



    https://www.homebuildingandrepairs.com/fences/index.html click on this link for more information about wood fence construction and home repairs. Watch this video to learn reasons why wood fence posts rot and fall apart. Moisture and water seems to be wood’s worst enemy and let’s face it in nature it’s part of the decomposition process, so there isn’t much we can do about it. However, if you understand what causes the wood post to rot, I’m pretty sure you can figure out a few ways to reduce these problems and extend the life of your fence. In other words, extend the life of your wood fence posts and save money in the future by reducing your future home repair bills. If this sounds good and you’re looking for some more interesting tips and ideas, visit our websites today area

    Related Products

    WhatsApp Online Chat !