Factory source manufacturing CV-709 silicone sealant for PV moudels for Slovenia Importers
Short Description:
Description CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949 Key Features 1. 100% silicone 2. No sag 3. high thixotropy 4. Water & weatherproof 5. For solar components involved in the base material has good bonding Basic Ap...
Adhering to the principle of "quality, service, efficiency and growth", we have gained trusts and praises from domestic and international client for Factory source manufacturing CV-709 silicone sealant for PV moudels for Slovenia Importers, We are sincerely looking forward to establishing good cooperative relationships with customers from at home and abroad for creating a bright future together.
Description
CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949
Key Features
1. 100% silicone
2. No sag
3. high thixotropy
4. Water & weatherproof
5. For solar components involved in the base material has good bonding
Basic Application
1.Solar module frame seal
2.The adhesive of the solar energy back to the terminal block
3.General industrial assembly with seal
Technical data sheet
| Test standard | Test project | Unit | value |
| Before curing——25℃，50%R.H. | |||
| specific gravity | g/ml | 1.34-1.40 | |
| GB13477 | Operating time | min | 15 |
| GB13477 | surface drying time（25℃，50%R.H.） | min | 40-60 |
| 3 days after curing——25℃，50%R.H. | |||
| Temperature range | ℃ | -55~200 | |
| GB13477 | Durometer Hardness | Shore A | 40~55 |
| The ultimate tensile strength | Mpa | ≥2 | |
| GB13477 | Breaking elongation | % | 300-600 |
| Aluminum bonding shear strength | Mpa | ≥1.5 | |
| Electrical properties | |||
| Breakdown voltage | Kv/mm | ≥20 | |
| Volume resistance | ohm.cm | 9E+14 | |
| Dielectric constant | 3.1@50Hz | ||
Certification
UL E339949; TUV
Color
Black, White
Package
300ml in cartridge * 24 per box, 500ml in sausage *20 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Tools Required:
- Drill with a hammer setting (SDS drill works best)
- Impact gun and Phillips bit
- 1/4″ Concrete bit
- Scissors
- Hammer
- Taping block (scrap piece of 2″ x 4″)
- Shop vacuum
Materials:
- Delta-FL (105 sq ft roll)
- Landscape Fabric
- 4′ x 8′ Sheet of 5/8″ OSB with tongue and groove
- 100% Clear silicone
- Tuck tape
- 1-3/4″ Phillips flat top Tapcon screws (approximately 8 per 4 ‘x 8′ sheet)
Laminate Floor: Life Stepp, country collection, colour: Gray Smoke, Size: 1215x126x12.3mm, SKU # 2717. Each box covers 19.77 sq ft.
Delta-FL in conjunction with 5/8″ OSB tongue and groove plywood is the perfect subfloor system for concrete and slab on grade floors. The plastic membrane is installed with the dimples down to create a 5/16″thick air space allowing the concrete slab to breathe. If there ever was a flood it would also allow the water to flow freely towards any drains. By installing this subfloor you will increase your floor temperature by 7 °C providing a warm and comfortable basement floor.
Music Credit:
Electro-Light – Symbolism [NCS Release]
Song Link: https://www.youtube.com/watch?v=__CRWE-L45k
Learn how to shrink a mold to reduce the size of an already existing original. Through a simple mold making technique you can shrink a mold by nearly 25 percent without re sculpting a smaller original. Visit www.alumilite.com for additional product information.
