Discount wholesale SV-800 General purpose MS sealant to Nigeria Manufacturers

Discount wholesale
 SV-800 General purpose MS sealant to Nigeria Manufacturers
  • Discount wholesale
 SV-800 General purpose MS sealant to Nigeria ManufacturersDiscount wholesale
 SV-800 General purpose MS sealant to Nigeria Manufacturers
  • Discount wholesale
 SV-800 General purpose MS sealant to Nigeria ManufacturersDiscount wholesale
 SV-800 General purpose MS sealant to Nigeria Manufacturers

Short Description:

Description General purpose and low modulus MSALL sealant is a high quality, single component, paintable, anti-polluting neutral modified sealant based on silane-modified polyether polymers. The product does not contain solvents, no pollution to the environment, while most of the building materials, without primer, can produce superior adhesion.   Product Features 〔1〕 environmental protection products: no solvent, no PVC, no isocyanate, non-toxic, tasteless, non-polluting, fast curing;...


Product Detail

Attentions

Application

Product Tags

Our goal is to provide high quality products at competitive prices, and top-notch service to customers around the world. We are ISO9001, CE, and GS certified and strictly adhere to their quality specifications for Discount wholesale SV-800 General purpose MS sealant to Nigeria Manufacturers, Standing still today and looking into the future, we sincerely welcome customers all over the world to cooperate with us.


Description

General purpose and low modulus MSALL sealant is a high quality, single component, paintable, anti-polluting neutral modified sealant based on silane-modified polyether polymers. The product does not contain solvents, no pollution to the environment, while most of the building materials, without primer, can produce superior adhesion.

 

Product Features

〔1〕 environmental protection products: no solvent, no PVC, no isocyanate, non-toxic, tasteless, non-polluting, fast curing;

[2] surface coating: compatible with most industrial paint, dry surface can be painted, so does not affect the curing speed;

[3] easy to use: excellent thixotropy and extrusion, for a wide temperature range.

〔4〕 good adhesion: the stone, aluminum, ceramics and cement components, and most of the building materials with excellent adhesion properties; no pollution of the porous material.

[5] excellent weather resistance, aging performance, superior tensile and compression resilience;

[6] neutral curing, stone, cement and other non-corrosive building materials, to overcome the common silicone rubber easy to contaminate the shortcomings of the substrate.

 

Basic use

General purpose and low modulus MSALL sealant Suitable for use:

[1] construction of housing and other areas of bonding and sealing;

[2] fixed panel, frame, window sill installation, suitable for a variety of building materials such as paint metal, glass, wood, concrete, stone, masonry and other ordinary seal;

[3] seam and ceiling seal;

[4] water pipes, roof gutter and other seals;

[5] activity room, container seal;

[6] interior decoration seal;

[7] mildew – suitable for kitchen and toilet applications;

〔8〕 the floor system of bonding, especially for housing renovation when the laying of tiles;

[9] on the porous material or smooth, moist surface has a strong adhesive force.

[10] Please note: MSALL sealant is not suitable for glass inlay use; for the prefabricated concrete displacement joint seal recommended supporting the use of Jiang special primer.

 

Technical data sheet
Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 density g/m³ 1.40±0.05
GB2793 Non-volatile components % 99.5
GB13477 Flow, sagging or vertical flow mm 0
GB13477 surface drying time(25℃,50%R.H.) min 45-60
  Curing speed mm/24h 3
Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.

14days after curing——25℃,50%R.H.

GB13477 Durometer Hardness Shore A 22-28
GB13477 The ultimate tensile strength Mpa 1.0
GB13477 elongation at break % 550

Color

White, black, grey

 

Package

300ml plastic cartridges

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • In this video, I test the strength of four different glues and adhesives. These tests aren’t exactly scientific but I wanted more of a “real world” test because I’m making UAV/quadcopter frames and you never know how you’re going to crash.

    ABOUT THE TESTS
    I made 4 wood frames from 1/16″ thick birch plywood. This is the same wood that I’m using to sandwich in between layers of carbon fiber in my frames. Glued to the bottom of each frame is 0.008″ thick woven carbon fiber sheet. This is very thin, lightweight stuff and all 4 pieces came from the same sheet.

    The carbon fiber sheet was sanded and all surfaces were cleaned thoroughly. All adhesives were mixed and applied according to their instructions.

    TEST 1 – BSI 30 Minute Slow Cure Epoxy
    BSI stands for Bob Smith Industries. This epoxy is sold in many hobby stores and I seen videos where people rave about how good it is. For this application it was the worst. While it is slightly flexible after it cures, its still brittle. All I had to do was crack a corner and I easily peeled off the carbon fiber with hardly any effort. This stuff is not going to work well with a frame that’s constantly flexing and its not going to hold up at all in a crash.

    TEST 2 – Loctite CA Professional
    I’ve heard good things about using CA (Cyanoacrylate or “Super Glue”) on carbon fiber but you can’t trust everything you read on the internet. I used CA quite a bit on my micro quads but I was gluing wood and plastic. Here, it was a tiny bit better than the BSI epoxy, but not much. It took a little more effort to separate the carbon fiber but once it started peeling away, it was the end. Just like hard epoxy, CA is too brittle and can’t handle flexing.

    TEST 3 – JB WELD Clear Weld
    This 2 part epoxy is a COMPLETELY different product from the original JB Weld. This is a 5 minute epoxy that comes in a handy syringe style applicator. I’ve always heard quick drying epoxies are brittle but this stuff remains very flexible! When I tried to peel a corner, it resisted quite well, to the point where the wood started to split first. I really was struggling to peel the carbon fiber away. The carbon fiber actually ripped before I could peel the entire piece away. Remember, I was using very thin carbon fiber sheet for these tests. When I peeled the last piece off, you can see the wood itself had separated, not the bond between the carbon fiber and wood.

    I would certainly recommend this product when you need to fix something in the field or you need to glue something that isn’t critical. The problem with gluing more complex things like a frame, is that it hardens too quickly.

    TEST 4 – 3M EC2216 Epoxy
    This stuff is pretty amazing but it has its drawbacks. First, its expensive. Its around $20 for a 1.45 oz tube. Also, it dries very slowly- 24 hours for handling strength and 7 days for full strength. All that aside, you can see how well it held up in my test. When I tried to peel a corner, it took considerable effort to do any damage and then the carbon fiber sheet ripped. I was able to tear the entire edge away while the remaining carbon fiber was still firmly attached to the wood. I tried it on the other end and the same thing happened. I ended up having to break the frame to get enough leverage to separate the wood from the carbon fiber. You can see me twisting one piece of wood all the way around and the bond still holds. This is an amazing adhesive.

    NOT SHOWN IN THIS VIDEO
    I had already tested 2 other glues that aren’t in this video because I didn’t want to waste more carbon fiber. I tested regular JB Weld and its too brittle. It behaved in a similar way to the BSI epoxy. I also tested Gorilla Glue. While its a great glue for foam and wood, it does not stick to carbon fiber at all.

    If you’ve been following my videos, you know I’ve built a replacement frame for my QAV400 that weighs less than half of the original frame but lacks torsional stiffness. I’m currently testing several designs for a strong, light frame that has good torsional properties as well. To follow along as I build new frames, see my QAV400 mods log:

    https://diydrones.com/forum/topics/qav400-mods-to-increase-flight-time

    If you’re planning to build a stock QAV400, its a great quad! Here’s my original build log that uses all of the factory parts:

    https://fpvlab.com/forums/showthread.php?33317-Rob215-s-QAV400-Build

    Current Specs:
    - DIY carbon fiber lower frame / Lumenier QAV400 upper frame
    - Lumenier FX2216-9 1100KV motors
    - Lumenier 30A SimonK ESCs
    - APM 2.6 flight controller with uBlox GPS/compass kit
    - 3D Robotics telemetry radio
    - FrSky X8R 2.4GHz receiver
    - Graupner 9×5 E-Props
    - QAV Quick-mount 2-axis brushless gimbal
    - GoPro Hero3 Black camera
    - Lumenier CS-600 FPV camera
    - Flytron TVS-2 remote camera switch
    - MinimOSD
    - ImmersionRC 5.8GHz 600mw Tx
    - ImmersionRC Uno 5800 V2 Rx
    - IBCrazy 5.8GHz Bluebeam Ultra antennas
    - Lumenier 5200mAh 4S battery

    Thanks for watching! Please Subscribe!! =)

    Related Products

    WhatsApp Online Chat !