China Manufacturer for SV-666 Neutral silicone sealant to Australia Manufacturers

China Manufacturer for SV-666 Neutral silicone sealant to Australia Manufacturers
  • China Manufacturer for SV-666 Neutral silicone sealant to Australia ManufacturersChina Manufacturer for SV-666 Neutral silicone sealant to Australia Manufacturers
  • China Manufacturer for SV-666 Neutral silicone sealant to Australia ManufacturersChina Manufacturer for SV-666 Neutral silicone sealant to Australia Manufacturers
  • China Manufacturer for SV-666 Neutral silicone sealant to Australia ManufacturersChina Manufacturer for SV-666 Neutral silicone sealant to Australia Manufacturers

Short Description:

Description SV-666 neutral silicone sealant is a neutral curing glue single component, the modulus of the. It is specially designed for windows and doors caulking sealing general plastic doors and windows. It has good adhesion to glass and aluminum alloy, and has no corrosion.   Where  to use It is fit for multiple purpose sealing and bonding applications to form a silicone rubber adhering to adjacent substrates e.g. glass, ceramic, tile, wood and metal.   Key Features 1. 100% silicone 2. Eas...


Product Detail

Attentions

Application

Product Tags

Our goal is to satisfy our customers by offering golden service, good price and high quality for China Manufacturer for SV-666 Neutral silicone sealant to Australia Manufacturers, We look forward to establish a long-term business relationship with your esteem co-operation.


Description

SV-666 neutral silicone sealant is a neutral curing glue single component, the modulus of the. It is specially designed for windows and doors caulking sealing general plastic doors and windows. It has good adhesion to glass and aluminum alloy, and has no corrosion.

 

Where  to use

It is fit for multiple purpose sealing and bonding applications to form a silicone rubber adhering to adjacent substrates e.g. glass, ceramic, tile, wood and metal.

 

Key Features

1. 100% silicone

2. Easy to use

3. Waterproofing and weatherproofing

4. Primerless adhesion to most building materials

5. 12.5% movement capability

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 Flow, sagging or vertical flow mm 0
GB13477 surface drying time(25℃,50%R.H.) min 30

GB13477

Operating time min 20
  Curing time(25℃,50%R.H.) Day 7-14
Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃,50%R.H.
GB13477 Durometer Hardness Shore A 28
GB13477 The ultimate tensile strength Mpa 0.7
  Temperature stability -50~+150
GB13477 Movement capability % 12.5

 

Certification

JC/T881-2001 12.5E;GB/T14683-2003 12.5E

 

Color

Black,White,Gray

 

Package

300ml in cartridge * 24 per box, 590ml in sausage *20 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Check out our blog for clickable links to the items below!
    Blog- https://www.heywandererblog.com/2017/06/diy-stock-tank-pool-everything-you-need.html
    Instagram- www.instagram.com/heywanderer
    E-mail- heywanderer@gmail.com

    Things you will need:
    - Stock tank (size of your choosing- ours is 8 ft.)
    - Above Ground Pool Pump
    - Weatherproof Silicone Sealant
    - Hole Saw with Arbor
    - Plunger Valves
    - Pool Outlet
    - 1-3 Rubber Washers (or Gaskets)
    - 1 Strainer Nut

    Other things you will need for maintenance:
    - Chlorine Tablets
    - Floating Pool Dispenser
    - Water Testing Kit

    Step 1- Find a nice level area to lay the stock tank on. If the area where you have chosen isn’t level, use sand or rocks to build up whatever side needs it. It is very important that your stock tank be level so there aren’t any unexpected leaks.
    Step 2- Cut holes in your stock tank. I’m not going to lie- this is a pain in the butt. We bought a hole saw with an arbor and it took two people to get through the metal. You will need two holes, one at the top and one at the bottom. In an above ground pool, these aren’t usually right on top of each other, but ours are. We haven’t ever seen this as a problem.
    Step 3- Start assembling the parts. In the pool pump package there is a packet with instructions, warnings and troubleshooting. This packet proved to be vital in the setup of the pool. I did end up getting 2 gaskets for the bottom section (the drain section), one for the inside of the pool and one for the outside. It only says you need one for the inside, but this was causing a drip for us. I also put thread seal tape around the connections that were closest to the pool. There are a lot of connections, and each one has a gasket, so you could probably get away without the tape. I didn’t put it on all the connections, the only ones that really seemed to matter were the ones that are connecting the hoses to the pool.
    Step 4- Apply silicone waterproof sealant around all crevices involving the input and output parts. I did this on the inside of the pool and the outside. And I applied it VERY HEAVILY and did two layers, allowing one to dry before the second was applied. Sealing these crevices is one of the most important parts. This is what is going to keep the water in the pool. Well all of these steps are leading up to keeping water in the pool, but if there is any chance that it’s going to be getting out, this is what will save you.
    Step 5- Test for leaks. Before I added water to the pool, I took a water bottle and poured a good amount of water on the input and output parts. You could also just use a water hose. I would make sure the hose wasn’t on full blast. You don’t want to accidentally penetrate the sealant.
    Step 6- Once you are sure there aren’t any leaks, fill the pool just above the bottom hole/output. Check again to see if any leaks have started. If there aren’t any, fill the rest of the pool up!
    Step 7- Turn the pump on. Make sure both plunger valves are open/unlocked. When you first do this water may not come out of the output, but there is a solution! Twist off the knob on top of the filter pump to let some air out. Some water may escape too and that’s okay, just be ready to screw it back on as soon as the water starts coming out.



    Where to buy? Visit us at https://www.hughcogroup.com/

    https://www.facebook.com/hughcogroup

    Coated with Nanotechnology Hydrophobic. Easy to clean with water. Spray the shirt with LiquidGlass Textile Protect. Allow 24 hrs to dry before contacting with water.

    Water repellent, breathable, washable, transparent and durable.

    Related Products

    WhatsApp Online Chat !