22 Years Factory Siway MG PU FOAM Supply to Poland

22 Years Factory Siway MG PU FOAM Supply to Poland
  • 22 Years Factory Siway MG PU FOAM Supply to Poland22 Years Factory Siway MG PU FOAM Supply to Poland

Short Description:

Description MG PU FOAM is the expansion, moisture curing, has the strong cohesiveness, elastic foam obturator structure; Save work to save time, reduce waste; High bond strength; Bubble can stick in the concrete, wood, metal, plastic, such as base material surface, but not including teflon, silicon resins;   Key Features 1. Noise silencing effect 2. Strong bonding strength 3. Water & weatherproof 4. Primerless adhesion to most building materials   Basic Application 1.Doors and Windows and...


Product Detail

Attentions

Application

Product Tags

"Sincerity, Innovation, Rigorousness, and Efficiency" is the persistent conception of our company for the long-term to develop together with customers for mutual reciprocity and mutual benefit for 22 Years Factory Siway MG PU FOAM Supply to Poland, Any requires from you will be paid with our best attention!


Description

MG PU FOAM is the expansion, moisture curing, has the strong cohesiveness, elastic foam obturator structure; Save work to save time, reduce waste; High bond strength;

Bubble can stick in the concrete, wood, metal, plastic, such as base material surface, but not including teflon, silicon resins;

 

Key Features

1. Noise silencing effect

2. Strong bonding strength

3. Water & weatherproof

4. Primerless adhesion to most building materials

 

Basic Application

1.Doors and Windows and wall body between the gap filling sealing, fixed bond

2.Language lab, studio, etc when decorating, gap to fill

 

Technical data sheet

Project

Value

Density, Kg/m³,Not less

10

Thermal conductivity,35℃,W/(m·K) no more than

0.050

Dimensional stability(23±2)℃,48,h no more than

5

Operating temperature

-10~+35℃

Optimum operating temperature

+18~+25℃

Temperature range(After curing)

-35~+80℃

Tensile bond strength

kPa

Not less

Aluminum plate

Standard condition,7d

80

Immersion,7d

60

PVC plate

Standard condition,7d

80

Immersion,7d

60

Cement Plate

Standard condition,7d

60

Shear strength,kpa,Not less

80

Foam expansion ratio,Not less

Standard value-10

 

Certification

JC 936-2004

 

Color

White

 

Package

750ml in Bottle * 12 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Other related videos:
    How to strip and repair tap gland-seal

    How to stop a monobloc tap outlet leaking (emergency repair)

    Earlier today I noticed some water on the floor near the kitchen sink so opened the unit and saw a bit of a leak from the main stopcock that controls flow of water from rising main into the house. Water was dripping from the gland seal. Unfortunately since this is the main way of turning off the water supply* I couldn’t isolate the actual stopcock which ironically is the isolating valve for the cold water supply. So as this was an emergency repair I had to use PTFE tape which is a product that everyone should have in their toolkit.
    Anyway – to carry out emergency repair;
    Turn off the stopcock and remove handle by unscrewing the cross-head screw in the end of shaft.
    Loosen off the gland seal retainer collar. The leak will worsen so put some old rags around it to mop up spills.
    Try to extract the old gland packing which is either rubber, fibre or leather. If the tap is in awkward place or the old seal is rock hard and too tight to remove, you then have to wrap several turns of PTFE tape around the shaft as near to the gland seal as possible.
    Now using a flat screwdriver and carefully push the tape right down into the gland seal (or what’s left of it)
    Now install the gland seal retainer collar and tighten it up.
    Now turn on the stopcock or tap/faucet and check for leaks. Ideally the old seal/packing is removed first but in the real world that sometimes doesn’t happen. If there’s still no leaks after a few hours then chances are you’ve fixed the problem. This is a ‘temporary repair’ so ultimately you will have to fit a new stopcock/tap/valve at some point. A useful tip is to regularly cycle any water supply valves, taps etc fully open and closed to keep them from sticking open or shut. Do this twice a year. Taps tend to seize more when they are fully open so it’s good practice to open them fully then back them off half a turn so the internal valve seat isn’t hard against the end stops.
    *If the main water supply stop valve is leaking you’ll either need a pipe freezing kit or hope there is a main water supply cut-off along with the water meter or supply from the mains water. Worth making a note of where the stopcocks and other valves are located on your property.

    Related Products

    WhatsApp Online Chat !