2017 wholesale price CV-709 silicone sealant for PV moudels Export to Australia

2017 wholesale price 
 CV-709 silicone sealant for PV moudels Export to Australia
  • 2017 wholesale price 
 CV-709 silicone sealant for PV moudels Export to Australia2017 wholesale price 
 CV-709 silicone sealant for PV moudels Export to Australia
  • 2017 wholesale price 
 CV-709 silicone sealant for PV moudels Export to Australia2017 wholesale price 
 CV-709 silicone sealant for PV moudels Export to Australia
  • 2017 wholesale price 
 CV-709 silicone sealant for PV moudels Export to Australia2017 wholesale price 
 CV-709 silicone sealant for PV moudels Export to Australia

Short Description:

Description CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949   Key Features 1. 100% silicone 2. No sag 3. high thixotropy 4. Water & weatherproof 5. For solar components involved in the base material has good bonding   Basic Ap...


Product Detail

Attentions

Application

Product Tags

All we do is always associated with our tenet " Customer first, Trust first, devoting on the food packaging and environmental protection for 2017 wholesale price CV-709 silicone sealant for PV moudels Export to Australia, We warmly welcome all perspective inquiries from home and abroad to cooperate with us, and look forward to your correspondence.


Description

CV709 is a high-performance silicone sealant, one-component oxime type room temperature curing silicone rubber, has excellent weather resistance, high thixotropy, after curing for solar components involved in the base material has good caking property, by TUV for environmental requirements of the ROHS, UL E339949

 

Key Features

1. 100% silicone

2. No sag

3. high thixotropy

4. Water & weatherproof

5. For solar components involved in the base material has good bonding

 

Basic Application

1.Solar module frame seal

2.The adhesive of the solar energy back to the terminal block

3.General industrial assembly with seal

 

Technical data sheet

Test standard Test project Unit value
Before curing——25℃,50%R.H.
  specific gravity g/ml 1.34-1.40
GB13477 Operating time min 15
GB13477 surface drying time(25℃,50%R.H.) min 40-60
3 days after curing——25℃,50%R.H.
  Temperature range -55~200
GB13477 Durometer Hardness Shore A 40~55
  The ultimate tensile strength Mpa ≥2
GB13477 Breaking elongation % 300-600
  Aluminum bonding shear strength Mpa ≥1.5
Electrical properties
  Breakdown voltage Kv/mm ≥20
  Volume resistance ohm.cm 9E+14
  Dielectric constant   3.1@50Hz

 

Certification

UL E339949; TUV

 

Color

Black, White

 

Package

300ml in cartridge * 24 per box, 500ml in sausage *20 per box

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Hard case foam liners just don’t hold up very long without reinforcement. Plasti-Dip synthetic rubber protective coating spray is the simple solution to this problem.

    Take a peek at a few foam gun container projects including a waterproof Pelican case for a 26.5mm Heckler and Koch flare gun.

    Video link showing the boat the flare kit was used on:



    Other related videos:
    How to strip and repair tap gland-seal

    How to stop a monobloc tap outlet leaking (emergency repair)

    Earlier today I noticed some water on the floor near the kitchen sink so opened the unit and saw a bit of a leak from the main stopcock that controls flow of water from rising main into the house. Water was dripping from the gland seal. Unfortunately since this is the main way of turning off the water supply* I couldn’t isolate the actual stopcock which ironically is the isolating valve for the cold water supply. So as this was an emergency repair I had to use PTFE tape which is a product that everyone should have in their toolkit.
    Anyway – to carry out emergency repair;
    Turn off the stopcock and remove handle by unscrewing the cross-head screw in the end of shaft.
    Loosen off the gland seal retainer collar. The leak will worsen so put some old rags around it to mop up spills.
    Try to extract the old gland packing which is either rubber, fibre or leather. If the tap is in awkward place or the old seal is rock hard and too tight to remove, you then have to wrap several turns of PTFE tape around the shaft as near to the gland seal as possible.
    Now using a flat screwdriver and carefully push the tape right down into the gland seal (or what’s left of it)
    Now install the gland seal retainer collar and tighten it up.
    Now turn on the stopcock or tap/faucet and check for leaks. Ideally the old seal/packing is removed first but in the real world that sometimes doesn’t happen. If there’s still no leaks after a few hours then chances are you’ve fixed the problem. This is a ‘temporary repair’ so ultimately you will have to fit a new stopcock/tap/valve at some point. A useful tip is to regularly cycle any water supply valves, taps etc fully open and closed to keep them from sticking open or shut. Do this twice a year. Taps tend to seize more when they are fully open so it’s good practice to open them fully then back them off half a turn so the internal valve seat isn’t hard against the end stops.
    *If the main water supply stop valve is leaking you’ll either need a pipe freezing kit or hope there is a main water supply cut-off along with the water meter or supply from the mains water. Worth making a note of where the stopcocks and other valves are located on your property.

    Related Products

    WhatsApp Online Chat !