18 Years Factory offer SV-900 Industrial MS polymer silicone sealant for Swaziland Importers

18 Years Factory offer
 SV-900 Industrial MS polymer silicone sealant for Swaziland Importers
  • 18 Years Factory offer
 SV-900 Industrial MS polymer silicone sealant for Swaziland Importers18 Years Factory offer
 SV-900 Industrial MS polymer silicone sealant for Swaziland Importers
  • 18 Years Factory offer
 SV-900 Industrial MS polymer silicone sealant for Swaziland Importers18 Years Factory offer
 SV-900 Industrial MS polymer silicone sealant for Swaziland Importers

Short Description:

Description It is one component, primer less, can be painted, high quality joint sealant based on MS polymer technology, ideal for all sealing and boding on all materials. It is solvent free, environmental protection product.   Where to use Sealing and bonding in housing area, bus, train, elevator, air conditioner, ventilation equipment. Used for installing fixed panel frame, windowsill threshold, and suitable for sealing on all materials surface, like painted metal, glass, wood, concret...


Product Detail

Attentions

Application

Product Tags

Our well-equipped facilities and excellent quality control throughout all stages of production enables us to guarantee total customer satisfaction for 18 Years Factory offer SV-900 Industrial MS polymer silicone sealant for Swaziland Importers, Our professional technical team will be wholeheartedly at your service. We sincerely welcome you to visit our website and company and send us your inquiry.


Description

It is one component, primer less, can be painted, high quality joint sealant based on MS polymer technology, ideal for all sealing and boding on all materials. It is solvent free, environmental protection product.

 

Where to use

Sealing and bonding in housing area, bus, train, elevator, air conditioner, ventilation equipment. Used for installing fixed panel frame, windowsill threshold, and suitable for sealing on all materials surface, like painted metal, glass, wood, concrete, marble, natural stone, granite, bricks, mirrors, aluminum, steel, lead, zinc, common plastics, polystyrene, polyurethane and so on. Sealing the joint of ceiling, timber, gaps of water pipe, gutter on roofs, moved rooms, container, marine. Apply for interior and exterior family decoration, like floor adhesive systems, particular for laying floor tiles, suitable for kitchen, bathroom.

 

Key Features

1. Paint able

2. Sealing most materials

3. Excellent adhesion

 

Technical data sheet
Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 density g/m³ 1.40±0.05
GB2793 Non-volatile components % 99.5
GB13477 Flow, sagging or vertical flow mm 0
GB13477 surface drying time(25℃,50%R.H.) min 30
  Curing speed mm/24h 3
Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.14days after curing——25℃,50%R.H.
GB13477 Durometer Hardness Shore A 32-38
GB13477 The ultimate tensile strength Mpa 2.5
GB13477 elongation at break % 400

Color

White, black, grey

 

Package

300ml plastic cartridges

 

Shelf life

12 months 

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Check out our blog for clickable links to the items below!
    Blog- https://www.heywandererblog.com/2017/06/diy-stock-tank-pool-everything-you-need.html
    Instagram- www.instagram.com/heywanderer
    E-mail- heywanderer@gmail.com

    Things you will need:
    - Stock tank (size of your choosing- ours is 8 ft.)
    - Above Ground Pool Pump
    - Weatherproof Silicone Sealant
    - Hole Saw with Arbor
    - Plunger Valves
    - Pool Outlet
    - 1-3 Rubber Washers (or Gaskets)
    - 1 Strainer Nut

    Other things you will need for maintenance:
    - Chlorine Tablets
    - Floating Pool Dispenser
    - Water Testing Kit

    Step 1- Find a nice level area to lay the stock tank on. If the area where you have chosen isn’t level, use sand or rocks to build up whatever side needs it. It is very important that your stock tank be level so there aren’t any unexpected leaks.
    Step 2- Cut holes in your stock tank. I’m not going to lie- this is a pain in the butt. We bought a hole saw with an arbor and it took two people to get through the metal. You will need two holes, one at the top and one at the bottom. In an above ground pool, these aren’t usually right on top of each other, but ours are. We haven’t ever seen this as a problem.
    Step 3- Start assembling the parts. In the pool pump package there is a packet with instructions, warnings and troubleshooting. This packet proved to be vital in the setup of the pool. I did end up getting 2 gaskets for the bottom section (the drain section), one for the inside of the pool and one for the outside. It only says you need one for the inside, but this was causing a drip for us. I also put thread seal tape around the connections that were closest to the pool. There are a lot of connections, and each one has a gasket, so you could probably get away without the tape. I didn’t put it on all the connections, the only ones that really seemed to matter were the ones that are connecting the hoses to the pool.
    Step 4- Apply silicone waterproof sealant around all crevices involving the input and output parts. I did this on the inside of the pool and the outside. And I applied it VERY HEAVILY and did two layers, allowing one to dry before the second was applied. Sealing these crevices is one of the most important parts. This is what is going to keep the water in the pool. Well all of these steps are leading up to keeping water in the pool, but if there is any chance that it’s going to be getting out, this is what will save you.
    Step 5- Test for leaks. Before I added water to the pool, I took a water bottle and poured a good amount of water on the input and output parts. You could also just use a water hose. I would make sure the hose wasn’t on full blast. You don’t want to accidentally penetrate the sealant.
    Step 6- Once you are sure there aren’t any leaks, fill the pool just above the bottom hole/output. Check again to see if any leaks have started. If there aren’t any, fill the rest of the pool up!
    Step 7- Turn the pump on. Make sure both plunger valves are open/unlocked. When you first do this water may not come out of the output, but there is a solution! Twist off the knob on top of the filter pump to let some air out. Some water may escape too and that’s okay, just be ready to screw it back on as soon as the water starts coming out.



    https://www.wacker.com/cms/en/products/brands/elastosil/elastosil.jsp?cid=so:youtube

    Could you imagine that a film as thin as the surface of an inflated balloon might be used to produce energy from ocean waves?
    Our ELASTOSIL® film is an ultrathin, high-precision film of crosslinked silicone rubber available in various layer thicknesses from 20 μm to greater than 400 μm and is manufactured under clean-room conditions entirely without solvents. It is especially suited for use as a dielectric medium in applications that employ electroactive polymers (EAPs).

    Related Products

    WhatsApp Online Chat !