14 Years manufacturer Siway MG PU FOAM to Casablanca Manufacturer
Short Description:
Description MG PU FOAM is the expansion, moisture curing, has the strong cohesiveness, elastic foam obturator structure; Save work to save time, reduce waste; High bond strength; Bubble can stick in the concrete, wood, metal, plastic, such as base material surface, but not including teflon, silicon resins; Key Features 1. Noise silencing effect 2. Strong bonding strength 3. Water & weatherproof 4. Primerless adhesion to most building materials Basic Application 1.Doors and Windows and...
We rely upon strategic thinking, constant modernisation in all segments, technological advances and of course upon our employees that directly participate in our success for 14 Years manufacturer Siway MG PU FOAM to Casablanca Manufacturer, We are glad that we are steadily growing with the active and long term support of our satisfied customers !
Description
MG PU FOAM is the expansion, moisture curing, has the strong cohesiveness, elastic foam obturator structure; Save work to save time, reduce waste; High bond strength;
Bubble can stick in the concrete, wood, metal, plastic, such as base material surface, but not including teflon, silicon resins;
Key Features
1. Noise silencing effect
2. Strong bonding strength
3. Water & weatherproof
4. Primerless adhesion to most building materials
Basic Application
1.Doors and Windows and wall body between the gap filling sealing, fixed bond
2.Language lab, studio, etc when decorating, gap to fill
Technical data sheet
Project |
Value |
||
Density, Kg/m³,Not less |
10 |
||
Thermal conductivity,35℃,W/(m·K) no more than |
0.050 |
||
Dimensional stability(23±2)℃,48,h no more than |
5 |
||
Operating temperature |
-10~+35℃ |
||
Optimum operating temperature |
+18~+25℃ |
||
Temperature range(After curing) |
-35~+80℃ |
||
Tensile bond strength kPa Not less |
Aluminum plate |
Standard condition,7d |
80 |
Immersion,7d |
60 |
||
PVC plate |
Standard condition,7d |
80 |
|
Immersion,7d |
60 |
||
Cement Plate |
Standard condition,7d |
60 |
|
Shear strength,kpa,Not less |
80 |
||
Foam expansion ratio,Not less |
Standard value-10 |
Certification
JC 936-2004
Color
White
Package
750ml in Bottle * 12 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
https://www.sincosilicone.com/
Email: info@sincosilicone.com
Silicone valve technology for low friction and sealing performance. Fully autoclavable to 134˚C. SwingTop™ Features. Lightweight in construction.
How to install Stans Notubes tire system.
Installation Guide:
Deflate and dismount the tyre.
Remove the inner tube.
See the yellow tape; this is the tape that seals the rim toward the spokes. This is Stans rim tape that is required to make rim air tight.
Install the valve and tighten the nut.
Mount the tyre back on the rim and try to inflate it.
If the tyre inflates and stays inflated for a couple of minutes it means
you can make tubeless with this combination of rim and tyre. You may need the air compressor for the job but most certainly a big pump. You cannot inflate the tire with small portable pumps.
Deflate the tyre and take it off the rim on one small section.
Shake the bottle and pour sealant into the tyre.
Turn the wheel with open section up and mount the tyre back on the rim.
Inflate the tyre.
Now shake the wheel and turn it around so the sealant will equally distribute
inside and seal all the gaps.
Place the wheel on a bucket and wait for a min or two then turn it over.
Check for the air bubbles with the soap and water. If you see any shake the wheel some more until the sealant seals the holes.