11 Years manufacturer SV-8800 Silicone Sealant for Insulating Glass for Kyrgyzstan Importers
Description SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material. Where to use It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU. Key Features 1. High Modulus 2. UV resistance 3. Low vapor and gas transmission 4. Primerless adhesion...
Assume full responsibility to meet all demands of our clients; achieve continuous advancements by promoting the growth of our clients; become the final permanent cooperative partner of clients and maximize the interests of clients for 11 Years manufacturer SV-8800 Silicone Sealant for Insulating Glass for Kyrgyzstan Importers, We will do our best to meet your requirements and are sincerely looking forward to developing mutual beneficial business relationship with you!
SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.
Where to use
It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.
1. High Modulus
2. UV resistance
3. Low vapor and gas transmission
4. Primerless adhesion to coated glass
5. 100% compatible to SV-8890
Technical data sheet
|Test standard||Test project||Unit||value|
|GB13477||Specific gravity(After mixing)||1.33|
|GB13477||surface drying time（25℃，50%R.H.）||min||80-188|
|7 days after curing——25℃，50%R.H.|
|GB/T 531||Durometer Hardness||Shore A||40|
|GB13477||The tensile modulus at 12.5% elongation||Mpa||0.18|
|The ultimate tensile strength||Mpa||0.92|
|GB13477||Elongation limit (fracture)||%||150|
Component A(Base) – White, Component B(Catalyst)- Black
1. Component A(Base): (190L), Component B(Catalyst) (18.5L)
2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)
If you want the TDS or MSDS or other details, please contact with our sales person.
Showing how I installed my timing chain kit on my engine. This can be done with the engine in the car by removing the accessories, mounts, valve cover, etc.
Although this is for a Saturn S-Series much of the concepts will translate to other vehicles too.
Even if you are conducting this repair in your car the visualizations shown here may help you better understand the project where filth and limited access may prevent you from seeing everything well in your car.
This car is for my 1995 SW2 using a block from a 1997 SL2 and a rebuilt head. This is how I did it and what I learned. Information may or may not be accurate.
Be sure to set engine to 90 degreest past #1 Top Dead Center prior to rotating your camshafts. Once your camshafts are in the correct position pin them in place to prevent movement, turn crank counter clockwise to number one TDC. Everything is now in the correct position to install the timing chain. After installing everything double check all marks and positions then unpin the timing sprockets and release the tensioner retainer. Verify the tensioner plunger extends. Be sure to lubricate everything prior to closing up.
Here is a photo detailing all of the fasteners I had to remove when I first did a timing kit with the engine IN the car:
1991-1998 Cars use a different timing kit than 1999-2001 model years. The procedure is very similar though.
I am using a PCI brand timing chain kit model TS13126 which includes…
1 Timing Chain
2 Chain Guides
2 Camshaft Sprokets
1 Crank Sprocket
1 Top Chain Guide
While your timing cover is off you might consider checking the oil pump which is located in the timing cover. Be sure the oil seals on each side of the crank are still in place prior to installing the timing cover.
When installing the timing cover clean all mating surfaces well and use a suitable RTV sealant or equivalent.
I used the following torque specs:
Top chain guide 14nm (8mm bolt x 2)
Cam Sprockets 74 ft lbs (15mm bolt, 1 per Sprocket)
Fixed chain guide 26nm (10mm bolt x 3)
Pivoting chain guide 26nm (10mm bolt x 1) be sure under bolt head is clean
Tensioner 14nm (10mm bolt x 2)
https://www.uttamrubtech.com Uttam Rubtech Machinery (P) Ltd is a professionally managed company and a trendsetter in the field of rubber mixing mill, hydraulic press machine, high-tech polymer and other rubber processing machines. Established in 1958, the company has progressed in leaps and bounds under the able patronage of S. Uttam Singh Dadial. His son S. Kuljit Singh Dadial and Grand Sons S. Amrit Pal Singh Dadial (Mechanical Engineer) and S. Samrit Pal Singh Dadial carries on his legacy.
The in-house capabilities include design, manufacturing, and complete machining capabilities, with full technical and engineering support. The services and machinery are currently being used in the tyre, shoe, conveyor belting, automotive, defense, mining, medical, custom mixing, floor tile, roofing and general rubber goods industries.
We Supply Complete Project For
1. Rubber / EVA Sandals, Sheets, Mid Soles etc.
2. Automotive Rubber Components, Rubber and Metal Bonded
3. Master Batch for Polymer processing
4. ‘O’ Ring and oil Seals
5. Tyre, Tube, Flap and Fork Lift Tyres
6. Conveyer Belts & Transmission Belts
7. Rubber Hoses, Fuel Hoses (Low Pressure / High Pressure) Cable for Energy
8. Synthetic & Natural Sheets for various Applications.
9. Rubber Components for Industrial Application.
10. Critical Rubber Component for Medical & Non Medical Application
11. Silicon Rubber Component (Medical Equipment & Key Pads)
12. Break & Clutch Components
13. Battery Containers
14. Reclaim & Crumbing
15. Industrial & Construction Application