100% Original Factory Siway MG PU FOAM for Naples Factories
Short Description:
Description MG PU FOAM is the expansion, moisture curing, has the strong cohesiveness, elastic foam obturator structure; Save work to save time, reduce waste; High bond strength; Bubble can stick in the concrete, wood, metal, plastic, such as base material surface, but not including teflon, silicon resins; Key Features 1. Noise silencing effect 2. Strong bonding strength 3. Water & weatherproof 4. Primerless adhesion to most building materials Basic Application 1.Doors and Windows and...
Adhering to the principle of "quality, service, efficiency and growth", we have gained trusts and praises from domestic and international client for 100% Original Factory Siway MG PU FOAM for Naples Factories, We hope to establish more business relationships with customers all over the world.
Description
MG PU FOAM is the expansion, moisture curing, has the strong cohesiveness, elastic foam obturator structure; Save work to save time, reduce waste; High bond strength;
Bubble can stick in the concrete, wood, metal, plastic, such as base material surface, but not including teflon, silicon resins;
Key Features
1. Noise silencing effect
2. Strong bonding strength
3. Water & weatherproof
4. Primerless adhesion to most building materials
Basic Application
1.Doors and Windows and wall body between the gap filling sealing, fixed bond
2.Language lab, studio, etc when decorating, gap to fill
Technical data sheet
|
Project |
Value |
||
|
Density, Kg/m³，Not less |
10 |
||
|
Thermal conductivity，35℃，W/(m·K) no more than |
0.050 |
||
|
Dimensional stability（23±2）℃，48，h no more than |
5 |
||
|
Operating temperature |
-10~+35℃ |
||
|
Optimum operating temperature |
+18~+25℃ |
||
|
Temperature range（After curing） |
-35~+80℃ |
||
|
Tensile bond strength kPa Not less |
Aluminum plate |
Standard condition，7d |
80 |
|
Immersion，7d |
60 |
||
|
PVC plate |
Standard condition,7d |
80 |
|
|
Immersion，7d |
60 |
||
|
Cement Plate |
Standard condition，7d |
60 |
|
|
Shear strength，kpa，Not less |
80 |
||
|
Foam expansion ratio，Not less |
Standard value-10 |
||
Certification
JC 936-2004
Color
White
Package
750ml in Bottle * 12 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
almost done ready to reinstall
Waterproof garments can lose their water repellency as dirt and oil break down the water repellent coating. If you notice that the fabric of your jacket is absorbing rather than repelling water, it may be time to reproof it.
1. Always wash your waterproof jacket first before re-proofing.
2. There are two types of clothing proofer to choose from; wash in or spray on. You will first need to decide which is most appropriate for you. Our proofers should not alter the look or handle of the fabric. It is however recommended that the products are tried on a small, inconspicuous test area before spraying on or washing into the garment.
3. If using a wash in proofer, such as our Performance Proofer, first pour the appropriate amount of the proofer into the detergent compartment. For the Performance Proofer this will be two caps full for one jacket and three caps full for two. Allow the washing machine to run through the complete wash and rinse cycle at 30 degrees. Heat helps to activate the product, so if the jacket’s care instructions allow it you can tumble dry the jacket on a low or medium heat.
4. If you’re using a re-proofer spray, such as our Technical Proofer, spray the product evenly on the outside of the jacket from approximately 15-20 cm away. Hanging the jacket on a washing line when spraying with the proofer will help maintain an even coating. Check the jacket carefully to ensure no areas of the fabric have been missed and wipe off any excess with a damp cloth. Allow the jacket to dry naturally. For high abrasion areas such as the elbows and shoulders, it’s recommended that a second coat of proofer is applied. Again, allow to dry naturally.
Shop: https://bit.ly/1fMaeAs
