10 Years Factory Siway SV-602 Epoxy Structural Adhesive A/B for Juventus Importers

10 Years Factory Siway SV-602 Epoxy Structural Adhesive A/B for Juventus Importers
  • 10 Years Factory Siway SV-602 Epoxy Structural Adhesive A/B for Juventus Importers10 Years Factory Siway SV-602 Epoxy Structural Adhesive A/B for Juventus Importers

Short Description:

Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.   Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...


Product Detail

Attentions

Application

Product Tags

The company upholds the philosophy of "Be No.1 in quality, be rooted on credit and trustworthiness for growth", will continue to serve old and new customers from home and overseas whole-heatedly for 10 Years Factory Siway SV-602 Epoxy Structural Adhesive A/B for Juventus Importers, Standing still today and looking into the future, we sincerely welcome customers all over the world to cooperate with us.


Description

SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.

 

Key Features

1. Room temperature curing Epoxy adhesive

2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)

3. Mix ratio of 1:1 by volume or by weight

4. Good mechanical property

5. Bonds a wide variety of building materials

6. Good waterproofing and chemical resistance

 

Basic Application

1, the external walls of stone material, ceramic and other hang bond;

2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;

3, concrete, stone and so on crack repair;

4, the structure of the localization, anchor, reinforcement and reinforcement.

 

Technical data sheet

The following data is for reference only and is not recommended for the specification

Shear strength Stainless steel-stainless steel/Standard conditions ≥18   JC887-2001
Pressure shear strength Stone-stone/ Standard conditions ≥12
Stone-stone/ The freeze-thaw cycle 50 times ≥10
Stone – stainless steel/ Standard conditions ≥12
Standard conditions:Temperature=23℃,relative humidity=50%,48 hours curing
attribute SV-602-A SV-602-B SV-602(After mixing)
Colour gray white grey
Density(g/cm³) 1.8 1.8 1.8
Viscosity(PaS) 200-400 150-250  
Effective operating time(23℃) N/A N/A 20min
           

 

Certification

JC 887-2001

 

Color

Part A-Grey Paste/Part B-White Paste

 

Package

9kg/9kg per unit and 15kg/15kg per unit

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • You should check the valves at 500 – 600 miles, then every 6,000 miles after that.

    Tools you’ll need:
    10 mm socket
    12 mm socket
    Medium ratchet with short AND long extension
    Big flat screwdriver or quarter
    19 mm socket
    Large ratchet
    Flat feeler gauge
    Torque wrench (one that works for low torques)
    16 mm wrench (optional)

    Need a Clymer manual? Check out https://www.clymer.com/ or https://www.youtube.com/user/ClymerManuals

    Body work removal and installation: https://www.youtube.com/watch?v=Kki7S2RZBGQ

    Remove the fan. The fan plug is mounted in a bracket on the frame – trace the wires, it’s easier than explaining. There are three 10 mm bolts. Two on the left and one near the center of the bike (right side of the fan) buried behind the radiator hose. The hose is pliable, push it out of your way. Use an extension. Unplugging the fan switch wire may also prove useful.

    Marknet Valve Check / Adjustment Procedures: https://www.klr650.marknet.us/valves.html
    I guess I lied. There is a link for the Clymers, but you still have to buy it: https://www.clymer.com/Book.aspx?bid=914&title=Kawasaki+KLR650%2c+1987-2006

    Unplug the spark plug wire (leave the spark plug alone! What did it ever do to you?) and the temperature sending wire (right next to the spark plug). Remove the ignition coil. It has two wires going into the back, unplug them, then remove the 10 mm bolts holing it in place.

    Remove the upper engine mount (I said I wasn’t going to to. *SPOILER ALERT* I tried to get the cover off for maybe 5 minutes to no avail. Then I gave in and took of the mount, the cover came out in about 10 seconds. Just do it). They are all 12 mm heads. Use the 16 mm wrench (not socket, like I said in the video… whoops.) to hold the plate “nut” from getting friendly with the engine.

    Snip the wire ties. Get rid of the gas tank rubber doodads. Clean as much of the bike above the valve area as you can.

    Take off the wire harness harness (two 10 mm bolts).

    Remove the valve cover bolts, all four are 12 mm. The two on the right are straight forward. The back left takes some wire wiggling, and the front left takes a lot of wire wiggling. Store the bolts in a safe place in such a way that you know where they go when you need to put them back in. Mind their gaskets.

    Valve stat sheet: https://www.klr650.marknet.us/valvclear.zip

    Remove the valve cover from the left side of the bike. Be careful: the surfaces are precision machined, screw up and the chance of leaks goes up. BE GENTLE! Gentle like it’s your girlfriend / wife / whathaveyou.

    Remove the two round plug on the left side of the engine. Use a big flat head screwdriver or a quarter. Use the 19 mm socket and large ratchet driver on the big hole and turn counterclockwise (the direction the wheels normally turn). There are three marks; you’re aiming for the third. It’s a straight tick mark with a T on right behind it. Watch the cam lobes. You’re at the “right” TDC (top dead center) when the tick mark by the T lines up with the lack of threads where the small cap goes AND the cam lobes all point away from each other. If you overshoot, take a breath, and spin the crank around TWICE. Watch the lobes if you’re wondering “why twice?”

    Use a flat feeler gauge and check your valve shim clearances. Watch the video for the explanation.

    Valve Shim Replacement: https://www.youtube.com/watch?v=R2d-V4udwaA

    Use RTV Silicone Sealant and make a thin coat on both sides of the gasket. Put the gasket in place. Put the valve cover back in place from the left side of the bike. Again, BE GENTLE. You’ve made it this far, don’t fubar your precision machined surfaces now.

    Replace the four cover bolts. Short on the left, long on the right. Tighten them evenly and carefully working your way up to 6 ft * lbs (that would be 71 INCH pounds).

    Put the ignition coil back on, plug in the two wires on the back of it, plug in the temperature sending wire and put the spark plug cap back on the spark plug.

    Put the fan back on (three bolts, 10 mm), plug it back in, put the plug back in its clip on the frame, plug the fan switch back in (bottom of the radiator).

    Replace the wire ties that you snipped.

    Replace the upper engine mount. All three bolts get torqued to 18 ft * lbs.

    Replace the Body Work (link is up top).

    Please rate and leave comments!

    For a wealth of KLR 650 information, please visit KLR650.NET – Your Kawasaki KLR650 Resource!
    If you decide to join, please use my referral link: https://www.klr650.net/forums/index.php?referrerid=17746



    Buy Axle Bearings here https://www.amazon.com/gp/product/B008OIG4FK/ref=as_li_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B008OIG4FK&linkCode=as2&tag=bullshitkor01-20&linkId=QOQYT6UIALXYDBN5
    Need a Slide hammer https://www.amazon.com/gp/product/B000I8R7EQ/ref=as_li_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B000I8R7EQ&linkCode=as2&tag=bullshitkor01-20&linkId=TQ3NFVWPOFHTRSY7
    Get the Bearing and Seal Driver Here https://amzn.to/1ZyDtIm
    I’ve seen some people go though all the trouble of removing the axles to replace a seal but I figure if you’ve gone that far for the price of a bearing you may as well toss a new one in with it.
    one way to tell if your axle seal is leaking is oil coming from the drums when the drum is removed you will seal oil leaking around the seal. Using a axle bearing remover and a slide hammer that bearing will come out in a matter of seconds. if you have a bad axle bearing you should be able to hear some rear end noise while driving. anyways it’s beer time

    https://twitter.com/bullshitkorner

    https://www.facebook.com/pages/Bullshitkorner/415124691917952

    Related Products

    WhatsApp Online Chat !