Well-designed SV-8000 PU Sealant for Insulating Glass for Malaysia Importers

Well-designed SV-8000 PU Sealant for Insulating Glass for Malaysia Importers
  • Well-designed SV-8000 PU Sealant for Insulating Glass for Malaysia ImportersWell-designed SV-8000 PU Sealant for Insulating Glass for Malaysia Importers

Short Description:

Description SV – 8000 two-component polyurethane insulating glass sealant is a neutral cure, mainly used for the insulating glass of the second seal. Product formulation to use its performance with high modulus, high strength, to meet the requirements of insulating glass assembly.   Where to use It is a two-component PU sealant that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.   Key Fe...


Product Detail

Attentions

Application

Product Tags

Adhering to the principle of "quality, service, efficiency and growth", we have gained trusts and praises from domestic and international client for Well-designed SV-8000 PU Sealant for Insulating Glass for Malaysia Importers, We, with great passion and faithfulness, are willing to provide you with perfect services and striding forward with you to create a bright future.


Description

SV – 8000 two-component polyurethane insulating glass sealant is a neutral cure, mainly used for the insulating glass of the second seal. Product formulation to use its performance with high modulus, high strength, to meet the requirements of insulating glass assembly.

 

Where to use

It is a two-component PU sealant that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.

 

Key Features

1. High Modulus

2. UV resistance

3. Low vapor and gas transmission

4. Primerless adhesion to coated glass

 

Technical data sheet

Test project standards Value
Sagging degree (mm) ≤3 0
Operating time ≥30 30
Thermal weight loss(%) ≤10 2
Durometer Hardness Shore A 20-80 42
tensile propcrties(MPA) >0.4 1.0
Bond damage area(5%) ≤5 0

 

Certification

GB-24266-2009;

 

Color

Component A(Base) – White, Component B(Catalyst)- Black

 

Package

1. Component A(Base): (190L), Component B(Catalyst) (18.5L)

2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)

 

Shelf life

12 months

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

 

  • Previous:
  • Next:



  • Check out our blog for clickable links to the items below!
    Blog- https://www.heywandererblog.com/2017/06/diy-stock-tank-pool-everything-you-need.html
    Instagram- www.instagram.com/heywanderer
    E-mail- heywanderer@gmail.com

    Things you will need:
    - Stock tank (size of your choosing- ours is 8 ft.)
    - Above Ground Pool Pump
    - Weatherproof Silicone Sealant
    - Hole Saw with Arbor
    - Plunger Valves
    - Pool Outlet
    - 1-3 Rubber Washers (or Gaskets)
    - 1 Strainer Nut

    Other things you will need for maintenance:
    - Chlorine Tablets
    - Floating Pool Dispenser
    - Water Testing Kit

    Step 1- Find a nice level area to lay the stock tank on. If the area where you have chosen isn’t level, use sand or rocks to build up whatever side needs it. It is very important that your stock tank be level so there aren’t any unexpected leaks.
    Step 2- Cut holes in your stock tank. I’m not going to lie- this is a pain in the butt. We bought a hole saw with an arbor and it took two people to get through the metal. You will need two holes, one at the top and one at the bottom. In an above ground pool, these aren’t usually right on top of each other, but ours are. We haven’t ever seen this as a problem.
    Step 3- Start assembling the parts. In the pool pump package there is a packet with instructions, warnings and troubleshooting. This packet proved to be vital in the setup of the pool. I did end up getting 2 gaskets for the bottom section (the drain section), one for the inside of the pool and one for the outside. It only says you need one for the inside, but this was causing a drip for us. I also put thread seal tape around the connections that were closest to the pool. There are a lot of connections, and each one has a gasket, so you could probably get away without the tape. I didn’t put it on all the connections, the only ones that really seemed to matter were the ones that are connecting the hoses to the pool.
    Step 4- Apply silicone waterproof sealant around all crevices involving the input and output parts. I did this on the inside of the pool and the outside. And I applied it VERY HEAVILY and did two layers, allowing one to dry before the second was applied. Sealing these crevices is one of the most important parts. This is what is going to keep the water in the pool. Well all of these steps are leading up to keeping water in the pool, but if there is any chance that it’s going to be getting out, this is what will save you.
    Step 5- Test for leaks. Before I added water to the pool, I took a water bottle and poured a good amount of water on the input and output parts. You could also just use a water hose. I would make sure the hose wasn’t on full blast. You don’t want to accidentally penetrate the sealant.
    Step 6- Once you are sure there aren’t any leaks, fill the pool just above the bottom hole/output. Check again to see if any leaks have started. If there aren’t any, fill the rest of the pool up!
    Step 7- Turn the pump on. Make sure both plunger valves are open/unlocked. When you first do this water may not come out of the output, but there is a solution! Twist off the knob on top of the filter pump to let some air out. Some water may escape too and that’s okay, just be ready to screw it back on as soon as the water starts coming out.



    My first experience with glazing putty was watching my Dad put new glass in the front window of our house on Crippen St. in Coldwater, MI. It was an old house and the putty was cracked and peeling so Dad cleaned out the old putty and put in new on the whole set of windows. I was fascinated and so were my brothers. Dad told us not to touch it because it took a while to set up. We covered the bottom of the windows with fingerprints checking every day for a couple weeks to see if it was set yet. Now that you’ve had a chance to visit and look around the place why not comment on what you see. Pointing fingers or pats on the back, all are welcome. Some of the best ideas come from you, the viewers.
    Shares – PLEASE share my videos. If I’ve done it right let your friends in on the secret. If not then let them in on the laugh.
    Subscribe ~ One click to hear about all the latest news and happenings here at the shop. https://www.youtube.com/user/oldsneelock?…
    Dislikes – Opinions differ. Not everyone will like what they see. But if you don’t like them, PLEASE comment to tell me why.
    Follow Old Sneelock on Face Book for behind the scenes photos, video, and back stories. https://www.facebook.com/pages/Old-Sneelocks-Workshop/252222441610151

    Related Products

    WhatsApp Online Chat !