Good quality 100% SV-800 General purpose MS sealant Supply to Turkey

The company upholds the philosophy of "Be No.1 in quality, be rooted on credit and trustworthiness for growth", will continue to serve old and new customers from home and overseas whole-heatedly for Good quality 100% SV-800 General purpose MS sealant Supply to Turkey, We welcome you to visit our factory and look forward to establishing friendly business relationships with customers at home and abroad in the near future.

Description

General purpose and low modulus MSALL sealant is a high quality, single component, paintable, anti-polluting neutral modified sealant based on silane-modified polyether polymers. The product does not contain solvents, no pollution to the environment, while most of the building materials, without primer, can produce superior adhesion.

Product Features

〔1〕 environmental protection products: no solvent, no PVC, no isocyanate, non-toxic, tasteless, non-polluting, fast curing;

[2] surface coating: compatible with most industrial paint, dry surface can be painted, so does not affect the curing speed;

[3] easy to use: excellent thixotropy and extrusion, for a wide temperature range.

〔4〕 good adhesion: the stone, aluminum, ceramics and cement components, and most of the building materials with excellent adhesion properties; no pollution of the porous material.

[5] excellent weather resistance, aging performance, superior tensile and compression resilience;

[6] neutral curing, stone, cement and other non-corrosive building materials, to overcome the common silicone rubber easy to contaminate the shortcomings of the substrate.

Basic use

General purpose and low modulus MSALL sealant Suitable for use:

[1] construction of housing and other areas of bonding and sealing;

[2] fixed panel, frame, window sill installation, suitable for a variety of building materials such as paint metal, glass, wood, concrete, stone, masonry and other ordinary seal;

[3] seam and ceiling seal;

[4] water pipes, roof gutter and other seals;

[5] activity room, container seal;

[6] interior decoration seal;

[7] mildew – suitable for kitchen and toilet applications;

〔8〕 the floor system of bonding, especially for housing renovation when the laying of tiles;

[9] on the porous material or smooth, moist surface has a strong adhesive force.

[10] Please note: MSALL sealant is not suitable for glass inlay use; for the prefabricated concrete displacement joint seal recommended supporting the use of Jiang special primer.

Technical data sheet

Color

White, black, grey

Package

300ml plastic cartridges

Shelf life

12 months

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

Walls and Floors have teamed up with BAL to bring you an easy-to-follow, step-by-step guide on how to waterproof a shower or wetroom, to get the area ready for tiling onto. Our professional tiler takes you through the process, and explains what he’s doing in layman’s terms.

If it’s time your bathroom had a refresh, and you’re looking to decorate your shower area, Walls and Floors have a great selection of tiles to choose from. We have thousands of stylish bathroom tiles – perfect for restrooms, water closets and en suites! The bath and shower area is a place where we can relax and underwind after a hard day’s work – that’s why it’s important that our bathrooms look nice. Moroccan Tiles are perfect for bringing a powerful, eye-catching, cultured appearance to your bathroom walls. Metro Tiles are also a winning choice when it comes to tiling a bathroom wall. For a textured, massaging feeling underfoot, try our River Pebble Tiles – sheets of smooth pebbles arranged in a mosaic formation. It’s important to use anti slip floor tiles when tiling a bathroom floor space. If you’re stepping in and out of the bath or shower with wet feet, you don’t want to slip over. Anti slip flooring adds a little more friction to your stride. Browse our selection of Bathroom wall and floor tiles now: https://www.wallsandfloors.co.uk/category/bathroom-tiles/

Waterproofing can be a less daunting task than it sounds, by using a product such as BAL Waterproofing Kit for Showers. It’s a simple, easy-to-use kit containing everything you need to waterproof the area.
When tiling any wet areas, for example the shower, or around a bath area, you must make some further considerations. Remember – grouts and adhesives are only water resistant and not waterproof. The main thing you need to do is waterproof the background that you’re going to be tiling onto.
In the video, our tiler uses in BAL WP1 kit. He shows you how to use it to waterproof your background, before you start to tile.
Before you begin, make sure you’ve got your safety wear on. Put on your gloves to protect your hands from any irritant substances, and wear goggles to prevent any nasty splashes from going in your eyes.
Also, make sure that you protect your shower tray. Put a protective sheet down. Make sure you mask up any fixtures or fittings that are exposed – such as the shower rail, etc. You’re then ready to start waterproofing the background.
Once you are happy that the background is in a fit and proper condition, and has been properly prepared, you can begin waterproofing. Firstly, pour some of the undiluted primer into a paint tray. And then, using a roller, simply paint the primer onto the walls. This will help remove surface dust, and will also aid adhesion. It is advised to start from the top of the wall and work down – just in case the primer slightly runs down the wall surface.
When priming, you should prime the walls the width of the shower tray and the height of the ceiling. This should be done on all walls that are in contact with the shower tray base. The primer is blue so that when you apply it to the walls, you can check that you have covered all areas. When the primer dries, the colour will fade. This should take approximately fifteen minutes, depending on the room temperature.
So once the primer is dry, you can then apply the WP1 coating to the same areas. Start by applying the coating first, fairly liberally – to all the corners, and where the walls meet the shower tray. Once this is done, cut the roll of tape to the required size, and place this into any corners and where the wall meets the tray. Push the tape to the wall; pushing out the air, and put another WP1 coating on top of the tape to secure in place.
When the first coat is dry, then apply a second coat of the waterproof coating. On the second coat, it is best to apply it to the wall in the opposite direction to that in which the first coast was applied. This will ensure that you have not left any gaps. So, all that’s left in the waterproofing kit is the polyester matting.
In the installation in the video, the tiler is working around a shower tray. It may be that you have a wet room floor, or a floor that has a timber construction. If this is the case, you can use the polyester matting, and apply in the same fashion, with the coating to add some strength and rigidity to the coating on the floor.
Once you’ve applied the second coat and this is dry, this will now be ready to tile and fully waterproof. However, we advise that you wait another 24 hours before you start to tile.
The last thing to remember is that on your final tile cut, you overlap the polyester tape. With a nice sharp Stanley knife, make sure you trim that off before undertaking any siliconing.

https://RAWMaterialSuppliers.com/ Call us at 877.788.6653 RAW Material Suppliers carries the best Silicone Putties in the world.

Our Mission is to provide an uninterrupted flow of materials to our customers while delighting them with our service, quality, product selection and technical knowhow.

Silicone putties are the swiss army knives of mold making. It’s easy to carry with you, you don’t need a scale to mix, it stays in place on a vertical surface and it’s extremely fast! I am sure you’re thinking of uses for it right now; they are endless!

Once you begin using our products, you will know why we have returning customers. Raw Material Suppliers is the best source for silicone putties with an all-inclusive line of products.

Our RAW Material Suppliers technical support application specialists are available for assistance with joint design, adhesive selection and the production process.

Fast is better than slow. We know you have a deadline and are here to help you beat it.

At Raw Material Suppliers we offer Tin (Condensation) and Platinum (Addition) cure silicone mold making rubber, and guidance on how to use these products.

Whether your need is for thin and pourable, thick and brush-able or for silicone putties, we offer the rubber you require to make an outstanding mold.

Some additional Silicone putty applications include: Jewelry Making and Repair, Small Impression Molding, Antique Furniture Repair, Soap Molds, Candle Molds, and Making Silicone Parts.

You can cast almost anything into a silicone putty mold: Chocolate & Candy, Urethane Casting Resin, Epoxy, Plaster, Concrete, Waxes, Clay, as well as Low Melt Metals such as Pewter and Lead.

We supply the following raw materials and many more:

-              Silicone Putties
-              Permabond Engineering Adhesives
-              Polyurethane Casting Resin
-              Hapco Casting Resin
-              Silicone Casting Resin
-              Aqua Resin
-              Mold Release Agents
-              Silicone Ink

Silicone Putties – Raw Material Suppliers