factory customized SV-900 Industrial MS polymer silicone sealant Wholesale to Juventus

factory customized SV-900 Industrial MS polymer silicone sealant Wholesale to Juventus
  • factory customized SV-900 Industrial MS polymer silicone sealant Wholesale to Juventusfactory customized SV-900 Industrial MS polymer silicone sealant Wholesale to Juventus
  • factory customized SV-900 Industrial MS polymer silicone sealant Wholesale to Juventusfactory customized SV-900 Industrial MS polymer silicone sealant Wholesale to Juventus

Short Description:

Description It is one component, primer less, can be painted, high quality joint sealant based on MS polymer technology, ideal for all sealing and boding on all materials. It is solvent free, environmental protection product.   Where to use Sealing and bonding in housing area, bus, train, elevator, air conditioner, ventilation equipment. Used for installing fixed panel frame, windowsill threshold, and suitable for sealing on all materials surface, like painted metal, glass, wood, concret...


Product Detail

Attentions

Application

Product Tags

We have a professional, efficiency team to provide quality service for our customer. We always follow the tenet of customer-oriented, details-focused for factory customized SV-900 Industrial MS polymer silicone sealant Wholesale to Juventus, Our aim is "blazing new ground, Passing Value", in the future, we sincerely invite you to grow up with us and make a bright future together!


Description

It is one component, primer less, can be painted, high quality joint sealant based on MS polymer technology, ideal for all sealing and boding on all materials. It is solvent free, environmental protection product.

 

Where to use

Sealing and bonding in housing area, bus, train, elevator, air conditioner, ventilation equipment. Used for installing fixed panel frame, windowsill threshold, and suitable for sealing on all materials surface, like painted metal, glass, wood, concrete, marble, natural stone, granite, bricks, mirrors, aluminum, steel, lead, zinc, common plastics, polystyrene, polyurethane and so on. Sealing the joint of ceiling, timber, gaps of water pipe, gutter on roofs, moved rooms, container, marine. Apply for interior and exterior family decoration, like floor adhesive systems, particular for laying floor tiles, suitable for kitchen, bathroom.

 

Key Features

1. Paint able

2. Sealing most materials

3. Excellent adhesion

 

Technical data sheet
Test standard Test project Unit value
Before curing——25℃,50%R.H.
GB13477 density g/m³ 1.40±0.05
GB2793 Non-volatile components % 99.5
GB13477 Flow, sagging or vertical flow mm 0
GB13477 surface drying time(25℃,50%R.H.) min 30
  Curing speed mm/24h 3
Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.14days after curing——25℃,50%R.H.
GB13477 Durometer Hardness Shore A 32-38
GB13477 The ultimate tensile strength Mpa 2.5
GB13477 elongation at break % 400

Color

White, black, grey

 

Package

300ml plastic cartridges

 

Shelf life

12 months 

 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

  • Previous:
  • Next:



  • Making a Cavity Pour Mold with Mold Max 30 RTV Silicone Rubber from Smooth-On.

    Our model is a hand-carved hard wood 3-dimensional figure. Drill an air release hole in to the middle of a baseboard. Secure model to baseboard with screws. Apply plastic wrap to the original model to protect the surface. Cover the model with 1/2-inch (1.3 cm) clay blanket. Create a 2-inch (5.1 cm) flange for registration. Build a 3-inch (7.6 cm) clay dividing wall and apply clay supports. Drill indentations in the baseboard to register shell. Build a clay pour spout and a 1/2-inch clay dam. Apply Sonite Wax to baseboard and then apply Ease Release 200 to the entire surface.

    Measure and mix duoMatrix NEO with a mix ratio of 2A:1B. Combine parts and mix thoroughly. For the first layer, apply a detail coat to the first half. Measure and mix duoMatrix NEO with chopped fiber. Apply this as the second layer. Apply a third layer of duoMatrix NEO without chopped fiber. A wood support leg is attached using duoMatrix NEO. Let cure for one hour.

    Once the NEO has cured, remove the dividing wall. Drill indentations into shell for registration. Build a clay dam and pour spout. Apply Sonite Wax to baseboard and exposed shell and then apply Ease Release 200 to the entire surface. Measure and mix NEO for the second half of the support shell, following the same procedure used to create the first half. Again, a wood support leg is attached using NEO and the shell is allowed to cure one hour at room temperature. A rasp is used to create a smooth flange edge, and then three holes are drilled through the support shell. Bolts will help secure the support shell during casting.

    Demold the support shell halves, remove the plastic wrap from the model, and then remove clay from the support shell. Create vent holes in support shell to allow air to escape. A 1/4-inch (6 mm) drill bit is used to drill holes through the support shell for a total of six air vents. Apply release agent to both the model and support shell. Register the support shell over the model and secure. Use bolts to hold the support shell halves together. Drywall screws are used to secure the support shell to the baseboard. Seal all seams with a hot glue gun. Place drinking straws into pre-drilled holes for air release, using clay to help secure and seal the straw. Only 1/4-inch of the straw will go into the support shell. IMPORTANT: Do not allow the drinking straws to touch the model. Trim the top two straws for easier access to the pour spout.

    Measure and mix Mold Max 30 silicone rubber. Then vacuum the Mold Max 30. After vacuuming, pour Mold Max 30 into the pour spout. Cap the top of the straws with clay to stop the flow of rubber, saving material. Continue to pour rubber until the cavity is filled. Let Mold Max 30 rubber cure for 16 hours at room temperature. Once cured, remove the support shell and rubber mold from the model. Perfect detail is captured from the original model.

    How to cast into the mold:

    The mold is first primed with auto body primer. Smooth-Cast 300 liquid plastic is measured, mixed, and poured into the mold. After three minutes, the liquid plastic turns to a solid. Let Smooth-Cast 300 cure for 10 minutes at room temperature. Remove the support shell and demold casting. A perfect reproduction! The casting is ready to be painted.

    Make It Now! with Smooth-On

    https://www.smooth-on.com/

    https://www.facebook.com/SmoothOn

    https://twitter.com/SmoothOn

    https://www.google.com/+smoothon

    Related Products

    WhatsApp Online Chat !