13 Years manufacturer SV-999 Structural Glazing Silicone Sealant for New Zealand Importers
Short Description:
Description SV – 999 silicone structural sealant is a one-component, neutral curing, designed for glass curtain wall, aluminum curtain wall, glass daylighting roof and metal structural engineering structural assembly silicone sealant. Show the effective physical properties and bonding performance Key Features 1. 100% silicone 2. No sag 3. Strong bonding strength 4. Water & weatherproof 5. Primerless adhesion to most building materials 6. 25% movement capability Basic Application...
We take "customer-friendly, quality-oriented, integrative, innovative" as objectives. "Truth and honesty" is our management ideal for 13 Years manufacturer SV-999 Structural Glazing Silicone Sealant for New Zealand Importers, We encourage you to make contact as we are looking for partners in our venture. We are sure you will find doing business with us not only fruitful but also profitable. We are ready to serve you with what you require.
Description
SV – 999 silicone structural sealant is a one-component, neutral curing, designed for glass curtain wall, aluminum curtain wall, glass daylighting roof and metal structural engineering structural assembly silicone sealant. Show the effective physical properties and bonding performance
Key Features
1. 100% silicone
2. No sag
3. Strong bonding strength
4. Water & weatherproof
5. Primerless adhesion to most building materials
6. 25% movement capability
Basic Application
1.Glass curtain wall, aluminum curtain wall structure adhesive seal
2.Glass daylighting roof, metal structure engineering
3.Insulating glass bonding
Technical data sheet
| Test standard | Test project | Unit | value |
| Before curing——25℃，50%R.H. | |||
| specific gravity | g/ml | 1.40 | |
| GB13477 | Flow, sagging or vertical flow | mm | 0 |
| GB13477 | Operating time | min | 15 |
| GB13477 | surface drying time（25℃，50%R.H.） | min | 40-60 |
| Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃，50%R.H. | |||
| GB13477 | Durometer Hardness | Shore A | 40 |
| The ultimate tensile strength | Mpa | 1.3 | |
| GB13477 | Tensile strength（23℃） | Mpa | 0.8 |
| GB13477 | Tensile strength（90℃） | Mpa | 0.5 |
| GB13477 | Tensile strength（-30℃） | Mpa | 0.9 |
| GB13477 | Tensile strength（flooding） | Mpa | 0.6 |
| GB13477 | Tensile strength（flooding – ultraviolet） | Mpa | 0.6 |
Certification
GB 16776；ASTM C1184
Color
Black
Package
300ml in cartridge * 24 per box, 500ml in sausage *20 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Hard case foam liners just don’t hold up very long without reinforcement. Plasti-Dip synthetic rubber protective coating spray is the simple solution to this problem.
Take a peek at a few foam gun container projects including a waterproof Pelican case for a 26.5mm Heckler and Koch flare gun.
Video link showing the boat the flare kit was used on:
How to install Stans Notubes tire system.
Installation Guide:
Deflate and dismount the tyre.
Remove the inner tube.
See the yellow tape; this is the tape that seals the rim toward the spokes. This is Stans rim tape that is required to make rim air tight.
Install the valve and tighten the nut.
Mount the tyre back on the rim and try to inflate it.
If the tyre inflates and stays inflated for a couple of minutes it means
you can make tubeless with this combination of rim and tyre. You may need the air compressor for the job but most certainly a big pump. You cannot inflate the tire with small portable pumps.
Deflate the tyre and take it off the rim on one small section.
Shake the bottle and pour sealant into the tyre.
Turn the wheel with open section up and mount the tyre back on the rim.
Inflate the tyre.
Now shake the wheel and turn it around so the sealant will equally distribute
inside and seal all the gaps.
Place the wheel on a bucket and wait for a min or two then turn it over.
Check for the air bubbles with the soap and water. If you see any shake the wheel some more until the sealant seals the holes.
